Manuals / Oki / Computer Equipment / Printer

Oki 490 manual From the back of the printer, locate the tractors

Models: 490

1 94

Download 94 pages 15.37 Kb

Page 45

5From the back of the printer, locate the tractors (1).

5From the back of the printer, locate the tractors (1).

6Open the lock levers (1) and move the right tractor (as viewed from the back of the printer) to the reference mark

(2) matching the width of the paper you are loading. Then close the lock lever on the right tractor:

ML491

ML490

Note: The movement of the right tractor is limited to ensure that the paper covers the paper sensor.

7Open the tractor covers.

Maintenance 45

Image 45

Oki 490 manual From the back of the printer, locate the tractors

Contents

59348401 User’s Guidee-Mail Address pubs@okidata.com Mailing AddressSafety These are some of the things to look for Chapter 3 Using Your Printer ContentsChapter 1 Introduction Chapter 2 Helpful HintsChapter 6 Troubleshooting Chapter 5 MaintenanceAppendix A Parts & Accessories Appendix C SpecificationsChapter 1 Introduction Printer FeaturesOki Data on the Internet High Speed Draft Mode 420 cps 10 cpi Utility Mode 269 to 472 cpsChapter 2 Helpful Hints Note This feature is normally turned offSaving Money Forms Tear-Off Saving TimeOperation Tips Controlling Access to the PrinterTop of Form TOF Turning the Platen KnobChapter 3 Using Your Printer Parts Identification Rear Feed Continuous FormsNote For rear feed, the paper lever must be forward Paper Guides Sheet Guide Paper Lever On-Off Switch Platen Knob Parts Identification Top Feed Single SheetsUsing Your Printer Control Panel Acoustic Cover openTop of Form TOF and Forms Tear-Off Top of Form TOFDetermining if Forms Tear-Off is Off or On Setting Top of Form TOF Forms Tear-Off OFF Default SettingThe printhead moves back to the left margin Forms Tear-Off Set to ON The SEL light goes off and the red alarm light comes onThe paper moves to the current TOF Setting Top of Form TOFTemporarily Changing the Top of Form Position Resetting Top of Form to the Factory DefaultForms Tear-Off Feature Potential Problems with Software PackagesDo not use Forms Tear-Off with labels or multipart forms Note The default setting for Forms Tear-Off is OFF Changing the Forms Tear-Off SettingPaper Park Manual Forms Tear OffChanging Paper Paths Continuous Forms toSingle SheetsUsing Your Printer 3 Swing the wire feed guide over onto the pull-up roller Single Sheets toContinuous Forms1 Press FF/LOAD to remove the single-sheet paper 2 Lower the sheet guide into the continuous-forms positionPrinthead Gap Make sure the printer is turned off before you open the access coverLQ Letter Quality LQ light on Print QualityUtility UTILITY light on HSD High Speed Draft LQ and UTILITY lights both onCourier Typefaces LQ ModeGothic OratorCharacter Pitch Epson LQ - factory setting Printer ResetEmulations Changing EmulationsMenu Mode Keys Chapter 4 Menu ModePrinting the Menu Settings Resetting the Menu to the Factory DefaultsEntering and Exiting Menu Mode Printing the Current Menu SettingsChanging the Menu Settings Menu Settings Table Settings Defaults are set in bold italicGroup 13.6 Menu Settings Table ContinuedSettings Defaults are set in bold italic GroupMenu Settings Table Continued 500 ms, 1 sec, 2 secSettings Defaults are set in bold italic GroupSettings Defaults are set in bold italic Menu Settings Table ContinuedGroup 32 Microline 490/491 User’s GuideInvalid, Valid Ready on Power Up, Ready on SelectMenu Settings Table Continued Settings Defaults are set in bold italicSettings Defaults are set in bold italic Menu Settings Table ContinuedGroup 34 Microline 490/491 User’s GuideAuto CR, Default =No Explanations of Menu ItemsAuto LF, Default = No Auto Feed XT, Default = InvalidSSD -9V, select SSD SSD +9V, select SSD+ DTR -9V, select DTR Selects the printer command set emulation you want to engage Wide carriage model only. Change to 13.6 to print on wide paper Choose the quality and typeface of printing Change to Double for double width and height printing Chapter 5 Maintenance Replacing the Ribbon Cartridge1 Make sure the printer is turned OFF Do not remove the ribbon shield 1 from the ribbon The printhead may be HOTRear Feed Loading PaperMaintenance Loading Rear Feed Paper from the Back of the PrinterCareful 3 Grasp the sheet guide. Lift it slightly, then slide it back44 Microline 490/491 User’s Guide 5 From the back of the printer, locate the tractors 8 Place continuous forms paper on the first two pins of either tractor Note If the paper is too loose or too tight it can cause jams13 Press FF/LOAD 48 Microline 490/491 User’s Guide Loading Rear Feed Paper from the Front of the PrinterML490ML491 9 Reinstall the sheet guide Note If the paper is too loose or too tight it can cause jams50 Microline 490/491 User’s Guide 11 Press FF/LOAD MaintenanceTop Feed Single Sheets If the paper does not feed in, remove it. Check the paper lever position. Make sure the ALARM light is on if it is flashing, hold the SHIFT key and press the CHARACTER PITCH/RESET key. Reload the sheet of paper Clearing Paper Jams Rear-Feed Paper JamsMake sure the printer is turned off before you open the access cover Make sure the printer is turned off before you open the access cover Rear-Feed, Repeating Paper Jams4 Remove any torn pieces of paper 3 Open the access cover 1 and remove the pull-up roller assembly Single-Sheet Paper Jams5 Reinstall the pull-up roller assembly and close the access cover MaintenanceCleaning the Housing Make sure the printer is turned off before you open the access cover58 Microline 490/491 User’s Guide Note Settings in your software application will normally Chapter 6 Troubleshootingoverride any settings in your printer driver General InformationProblem Problems / SolutionsSolution Nothing happens when I turn on the printerSolutions The printer does not print when the computer sends dataProblem ProblemIve installed a new ribbon and the printing is smeared and streaked Ink smears on the paper when I print narrow columnsProblem SolutionThe ALARM light is on and the Character Pitch 10 light is flashing The ALARM light is flashingThe ALARM light is on and the Character Pitch 15 light is flashing There are dots missing in my printoutsContinuous-form paper sticks to the sheet guide The printer needs paper. The ALARM is not on. I can’t load paperProblem SolutionPurchasing Parts & Accessories Appendix A Parts & AccessoriesPower Cord Replacement PartsAccess Cover Pull-Up Roller AssemblyOption AccessoriesPull Tractor, Top-Mount 70030501Appendix B Printer Control Codes Epson LQ CommandsEpson LQ Commands Continued Epson LQ Commands Continued Epson LQ Commands Continued IBM Proprinter X24e / XL24e and IBM X24e AGM / XL24e AGM Commands IBM Commands continued IBM Commands Continued Note Specifications are subject to change without notice Appendix C SpecificationsPrint Method PrintheadEmulations co-resident Graphics ResolutionPrint Speed Characters per Line cplBar Codes Resident FontsResident Typefaces SpecificationsSingle Cut Sheets Paper Specifications ML490Single-part, continuous forms Carbonless continuous forms orig. + 4 copiesPaper Specifications ML491 Note Height dimensions do not include the acoustic cover Physical SpecificationsEnvironmental Requirements Electrical RequirementsAppendix D Installation LocationUnpack 3 Remove the shipping restraint from the pull-up roller assembly 2 Remove the printhead shipping restraint82 Microline 490/491 User’s Guide Installation 1 Make sure the printer is turned OFF Install the Ribbon CartridgeThe printhead may be HOT Do not remove the ribbon shield 1 from the ribbonComputer Connections Power ConnectionParallel LPT IEEE 1 Make sure both the printer and the computer are OFFUSB Specification 1.1 Compliant Loading Paper86 Microline 490/491 User’s Guide Font Sample Test Testing the PrinterThe printer prints the rolling ASCII text page after page Rolling ASCII TestPrinter Drivers Hexadecimal Dump ModeEmulations Using a Compatible Driver Loading the OKI DriverThe Windows Add New Hardware Wizard window displays Index 92 Microline 490/491 User’s Guide Index 94 Microline 490/491 User’s Guide