Olympus PT-022 E-39

E-39

Q11

:

Please tell me about repairs.

A11

:

Please contact a service station of OLYMPUS CORPORATION or your

dealer, if repair should be necessary. Do not try to repair, disassemble or

modify the Case yourself. Repair, disassembly or modification by you or

third parties not authorized by Olympus invalidates the guarantee.

Q12

:

What are the model numbers and the prices of the PT-022 accessories?

A12

:

The following accessories are being sold.

(1)O-ring for the PT-022 body (POL-022/¥1,050 with tax): This is a silicone

rubber O-ring packing to be installed in the PT-022 body to make it

waterproof. O-rings for other Case models cannot be used.

(2)Silicone O-ring grease (PSOLG-1/¥840 with tax): This is a special

grease for silicone O-ring maintenance.

(3)Silica gel (SILCA-5/¥525 with tax): This is a desiccant used to prevent

fogging of the glass parts of the Case. The quantity is five bags.

(4)LCD hood (PFUD-04/¥1,050 with tax): This hood is installed on the LCD

monitor window of the Case to make it easier to see the LCD monitor of

the camera.

(5)Balance weight for PT-022 (PWT-022/¥2,625 with tax): This is a weight

intended to bring the Case close to neutral buoyancy in sea water. Under

consideration of the environment, no lead is used.

❈You can order in large computer shops and camera mass sale stores.

❈Please contact your dealer or a service station of OLYMPUS

CORPORATION when replacement is required. Replacement will be

made against payment.

Q13

:

How can I take good underwater photos?

A13:

Olympus's ZUIKO CLUB online school website has a page describing

underwater shooting techniques. You can access this page at the

following link:

URL: http://www.olympus-zuiko.com/school/index.html

Contents

Main Instruction Manual PT-022 Underwater Case E-1 Introduction Please read the following items before use For safe use WARNING E-2 WARNING E-3 Batteries E-4 For Prevention of Water Leakage Accidents E-5 Handling the Product E-6 E-7 Contents Contents 1.Preparations ............................................................E-9 2.Advance Check of the Case 3.Install the digital camera. E-8 4.Taking Pictures Under Water 5.Handling After Shooting 6.Maintaining the Waterproof Function 7.Appendix Page E-10 Names of the parts Note: E-11 Install the strap. Master the basic operation. Holding the Case Installation explanation E-12 How to Press the Shutter How to Use the Zoom Lever How to Use the Mode Dial Mode dial knob E-13 Setting the Zoom Lever How to switch the power ON C-760 Ultra Zoom E-14 C-770 Ultra Zoom Page E-16 Removing the TLL cable connector cap ---- How to attach the TTL cable connector cap to the case ---- E-17 Removing the hot shoe cable cap 1 3 Cleaning the TTL connector E-18 2. Advance Check of the Case Advance test before use Advance Test E-19 3. Install the digital camera. E-20 Check the operation of the camera. Load the digital camera. Open the Case. Pull up the mode dial of the case. E-21 Insertion of silica gel Set the mode dial. E-22 Seal the Case. Install the special balance weight. Check the loading status. E-23 E-24 E-25 Final Test E-26 4. Taking Pictures Under Water How to Use the Hand Strap Take pictures carefully. Confirm the picture on the LCD monitor. Quietly press the shutter lever. E-27 5. Handling After Shooting Wipe off any waterdrop. E-28 Take out the digital camera. E-29 Wash the Case with pure water. Dry the Case. E-30 6. Maintaining the Waterproof Function Remove the O-ring. Remove any sand, dirt, etc. E-31 E-32 Install the O-ring. How to Apply Grease to the O-ring E-33 Maintenance of the threaded sections on the TTL cable and TTL cable connector Maintenance of the TTL Connector Cap E-34 Replace consumable products. 1 2 E-35 7. Appendix Q & A on the use of the PT-022 E-36 E-37 E-38 E-39 E-40 After-sale Service E-41 Specifications Diver's Insurance Guide