Connecting the Power/Turning on the DVD Receiver

Before connecting

Make sure that all the connections from pages 10 to 15 are complete (the connection to the TV is required).

Turning on the DVD Receiver may cause a momentary power surge, which might interfere with other electrical equipment such as computers. If this happens, use a wall outlet on a different circuit.

Thank you for your purchase of Our DVD-Video Player. Please make a selection

for On-Screen Language and your TV shape and press ENTER button on your remote control.

FIRST SETUP

On-Screen Language ENG

TV Shape

4:3LB

STANDBY/ON

STANDBY

POWER

ON OFF

PHONES

1 Connect the power cord (mains lead) to a wall outlet (the mains).

2 Press the POWER switch to

switch on the main power.

The DVD Receiver enters standby mode.

The STANDBY indicator lights up.

STANDBY

Notes

To switch off the main power, press the POWER switch again.

The buttons on the remote controller don’t operate if the POWER switch is set to OFF.

 

 

 

 

 

Before operating the cursor

 

 

 

 

 

Press MODE DVD or MODE AUDIO.

 

 

 

 

MASTER VOLUME

 

 

 

 

DISPLAY

ACOUSTIC

 

 

 

 

 

 

 

CONTROL FM MODE

 

 

 

 

 

 

 

 

DVD / CD

 

 

 

 

ON

S

TNB

INPUT

 

 

 

 

P

 

Y

 

PRESET

 

SUBWOOFER

SPEAKER SPEAKER

L

 

 

 

 

TUNING/PRESET MEMORY

SURROUND STEREO

S

 

 

 

 

 

T – D MODE

A / B SETUP

 

 

 

 

3 Press STANDBY/ON on the DVD Receiver or ON on the remote controller.

 

 

 

 

 

 

UT

SEL

 

 

 

 

 

 

 

 

 

ECT

OR

 

 

 

 

INP

 

 

 

 

 

 

 

 

 

MODE

 

 

 

 

 

 

 

VD

 

TA/

 

 

IO

 

 

D

 

 

 

MD

 

 

 

ING MODE

 

 

D

 

 

 

U

 

EN

 

 

 

 

 

 

A

 

T

 

 

 

 

 

 

 

 

IS

 

 

 

EO

T

 

 

 

L

 

 

 

 

 

 

 

 

 

ER

 

 

D

 

 

 

 

ST

 

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

U

 

 

 

 

 

 

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E

 

M

 

 

 

 

 

 

L

 

 

E

N

 

 

 

 

IT

 

 

 

 

 

 

 

 

T

 

 

 

 

 

U

TV

A.CTR L

The DVD Receiver turns on.

 

The light and display on the DVD Receiver’s

 

front panel light. At the same time, the

DVD / CD

STANDBY indicator goes off.

 

CH

 

 

 

 

ENTER

 

 

 

VOL

TUN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

 

P

 

 

E

 

 

 

 

U

 

 

 

 

T

 

 

ET

 

R

 

 

 

 

U

RN

S

 

 

 

 

 

 

 

 

 

C

 

REPEAT

 

 

 

 

/V

 

MUTING

 

 

 

 

 

TV

 

 

 

The first time you turn on the DVD Receiver, the FIRST SETUP screen appears. In the FIRST SETUP screen, select the On-Screen Language and TV Shape according to the aspect ratio of the TV screen (see pages 52 and 53).

1Press / to select “On-Screen Language,” then press

ENTER.

2Select a language with /, then press ENTER.

3Press to select “TV Shape,” then press ENTER.

4Press / to select the aspect ratio of the TV screen, then press ENTER.

5Finally press SETUP.

All of your selections are set and the FIRST SETUP screen disappears.

ENTER

ENTER

A – B

DIMMER

RECOPEN/CLOSE

RANDOMSLOW

SUBTITLE – ON / OFF ANGLE ZOOM

MEMORY CLEAR AUDIO DISPLAY

Notes

 

P

T

 

 

 

SE

U

R

 

 

 

C

 

 

/V

 

• To turn off the DVD Receiver, press STANDBY/ON on the DVD

TV

 

 

Receiver, or STNBY on the remote controller. The DVD Receiver enters standby mode. Be sure to set the volume to minimum before turning off the DVD Receiver.

You can change the above settings later with “Customizing the Function Settings” on page 50.

SW MODE TEST TONE

 

1

2

3

LATE NIGHT DISTANCE

 

4

5

6

SP A

CH SEL

 

7

8

9

SP B

T– D SETUP

UP/ DOWN

+10

0

SEARCH

-- / ---

16

Page 16
Image 16
Onkyo DR-S2.0 instruction manual Connecting the Power/Turning on the DVD Receiver, DVD Receiver enters standby mode