Onkyo DR-S2.0 instruction manual Changing the Sound Signal Conversion Method

Changing the Sound Signal Conversion Method

	EEP	ON		STNBY
SL
		INPUT	S	L
			E ECTOR
		MO DE
	O	DVD	M	TA/MD		TV
		ENING
UDI			ODE
A	IST			T – D
	L	STEREO				A.
	R
	R					C
	U						TR
S							L
		LE		ME	NU
		TIT

The reproduced disc sound will be output in the most suitable format automatically through the connected speakers and output connector/jacks on the DVD Receiver when “Audio Out Select” in the setting menu is set to “Bitstream” (see page 54).

However, you may need to convert the sound format in different ways depending on your purpose and preference.

For example, when you wish to:

•Listen to the high-frequency (kHz)/high-quantization (bit) format source in its original sound quality (see below), or

•Record the DVD video sound reproduced in the DOLBY DIGITAL format using recording equipment such as an MD recorder connected to the DIGITAL OUTPUT (OPT) connector on the DVD Receiver (see next page).

Press MODE DVD or MODE AUDIO first

VD	IO
	D
D	U
	A

/	CH			ENTER			VOL
	TUN
		R				P
			ET	URN	SE	R
	REPEAT				TV		MUTING
	A – B				DIMMER
	REC					OPEN/CLOSE
AUDIO	RANDOM						SLOW
	SUBTITLE – ON / OFF				ANGLE		ZOOM
CLEAR	MEMORY CLEAR				AUDIO		DISPLAY
	SW MODE TEST TONE
	1			2			3
	LATE NIGHT DISTANCE
	4			5			6
	SP A			CH SEL
	7			8			9
	SP B T– D SETUP					UP/ DOWN
	+10			0			SEARCH

-- / ---

This function enables you to temporarily change the sound signal conversion method which has been selected automatically according to the automatic setting in the setting menu (see pages 50 and 54).

DVD VCD CD

Changing the Sound Signal Conversion Method Temporarily

1	Press AUDIO during playback.
	The current audio setting is displayed for
Remote controller	about 3 seconds.
only
AUDIO				See previous
		Audio: 1	ENG PCM 2CH
		Audio OUT Select : Bitstream		page.
		The current sound signal
		conversion method
2	Press		/ while the audio setting is
	displayed on the TV screen.

ENTER

Audio: 1 ENG PCM 2CH

Audio OUT Select : 96k Sound

Each time you press /, the setting changes as follows:

Bitstream ↔ 96k Sound ↔ PCM

↑ ↑

For details about “Bitstream,” “96k Sound,” and “PCM,” see the explanation on page 54 and the table on the opposite page.

To turn off the audio setting display

CLEAR

Press CLEAR.

Notes

•The “Audio Out Select” setting in the setting menu (see page 54) is for automatic selection of the sound conversion method when the disc is inserted. Therefore, the selection in this section will not change the setting of “Audio Out Select” in the setting menu.

•When you turn on the DVD Receiver or replace a disc, the DVD Receiver returns to the automatic setting in the setting menu. (See page 54.)

DVD

To Listen to a High-Frequency/High- Quantization Format Source in its Original Sound Quality – 96k Sound

The high frequency/high quantization sound signals below are converted into 48 kHz/16 bit sound signals and sent to the speakers when the “Audio Out Select” (sound signal conversion method) is set to the standard setting, “Bitstream.”

High frequency/high quantization signals

•48 kHz/24 bit

•96 kHz/16 bit

•96 kHz/20 bit

•96 kHz/24 bit

To listen to the high-frequency (kHz)/hight-quantization (bit) format sounds in their original sound quality, follow the steps below.

1	Change the sound signal
	conversion method to “96k Sound”
	following the steps on the left.
	See a in the table titled “Sound from the
	speakers” on the opposite page.
	The DVD videos recorded in 48 kHz/24 bit,
	96 kHz/16 bit, 96 kHz/20 bit, and 96 kHz/
	24 bit are reproduced through the
	speakers at the same kHz and bit rate
	respectively.

2	If a subwoofer is connected, set the
	subwoofer mode to “SW Off.”
	See “Setting the Subwoofer Mode” on
	page 17.
3	Change the sound to stereo.
	See “Changing the Sound to Stereo” on
	page 36.

46