Onkyo instruction manual Powering Up & Setting Up the HT-R510, Powering Up the HT-R510

Powering Up & Setting Up the HT-R510

STANDBY/ON

DIGITAL INPUT

TAPE

STANDBY/ON

MASTER VOLUME

STANDBY/ON

DIRECT

STEREO

SURROUND

DSP

STANDBY

PRESET/ADJUST

A SPEAKERS B

DISPLAY

DIMMER

DIGITAL INPUT

SUBWOOFER

MEMORY

FM MODE

TUNING

SPEAKER ADJUST

AUDIO ADJUST

MODE

PHONES

AUDIO

DVD

VIDEO 1

VIDEO 2

VIDEO 3

TAPE

TUNER

C D

VIDEO 3 INPUT

SELECTOR

CABLE/SAT

VCR

S VIDEO

VIDEO

L AUDIO

R

CD/DVD

Input selector buttons

Powering Up the HT-R510

Before connecting the power cord, connect all your speakers and AV components (see page 10 to page 23).

1	Connect the power cord to a suit-
	able wall outlet.

Turning on the HT-R510 may cause a momentary power surge that might inter- fere with other electrical equipment on the same circuit. If this is a problem, plug the HT-R510 into a different branch cir- cuit.

If, for example, you connect your DVD player’s optical dig- ital audio output to the HT-R510’s OPTICAL 1 DIGITAL INPUT, you’ll need to change the DVD input source assign- ment from COAXIAL to OPTICAL 1.

You can change the assignments as follows.

1			Press the input selector button for
DVD	VIDEO 1	VIDEO 2	VIDEO 3 the source that you want to assign:
			[DVD], [VIDEO 1], [VIDEO 2],
	VCR		[VIDEO 3], [TAPE], or [CD].
	TAPE	TUNER
			C D
			The selected source appears on the dis-
			play. (The value next to the input source is
			the volume setting.)
2			Press the [DIGITAL INPUT] button.
	DIGITAL INPUT		The current source assignment appears, as
			shown.
3			Use the [DIGITAL INPUT] button to
	DIGITAL INPUT		select COAX (COAXIAL), OPT1

(OPTICAL 1), OPT2 (OPTICAL 2), or

– – – – (no assignment).

2

STANDBY/ON

Remote controller

Press the [STANDBY/ON] button.

The HT-R510 comes on, the display lights up, and the STANDBY indicator goes off.

To turn off the HT-R510, press the [STANDBY/ON] button. The HT-R510 will enter Standby mode. To prevent any loud surprises the next time you turn on your HT-R510, always turn down the vol- ume before turning it off.

If you’ve connected a MiniDisc recorder to the TAPE

inputs, you can set the HT-R510 so that “MD” appears on the display instead of “TAPE.” Simply press and hold the [TAPE] button until “MD” appears (about two seconds).

Notes:

•	For AV components that are connected to only analog
	inputs, choose the “– – – –” setting.
•	If you don’t press the [DIGITAL INPUT] button for three
	seconds, the previous display reappears.

Important—Assigning Digital Inputs to Input Sources

With this function you can assign AV components (i.e., input sources) with digital audio outputs to the HT-R510’s digital inputs. You only need to change these assignments if your connections don’t match the default assignments listed in the following table.

Input source	DIGITAL INPUT
DVD	COAXIAL
VIDEO 1	Not assigned
VIDEO 2	OPTICAL 2
VIDEO 3	Not assigned
TAPE	Not assigned
CD	OPTICAL 1

• You can also specify a signal format for the DIGITAL

INPUTs (page 28).

See page 28 for information on playing your AV compo- nents through the HT-R510.

To get the most out of your HT-R510, you should also set the functions on pages 25 through 27.

24