LPF of LFE

(Low-Pass Filter for the LFE Channel)

`80Hz, 90Hz, 100Hz, 120Hz

Advanced Operations

Speaker Distance

 

Level Calibration

`Off:

Low-Pass Filter is not applied.

With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

Note

• If you’re using THX-certified speakers, select “80Hz”.

Double Bass

This setting is NOT set automatically by

Audyssey 2EQ® Room Correction and Speaker Setup (page 32).

`On

`Off(THX)

Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer.

Note

When the “Subwoofer” setting is set to “No” or the “Front” setting to anything other than “Full Band”, this setting is fixed to “- - -”.

This setting is set to “On” automatically when the “Subwoofer” and “Front” settings are set for the first time to “Yes” and “Full Band” respectively.

If you’re using THX-certified speakers, select “Off(THX)”.

This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup (page 32).

Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.

Unit

`feet:

Distances can be set in feet. Range: 1.0ft to 30.0ft in

1.0foot steps.

`meters:

Distances can be set in meters. Range: 0.30m to 9.00m in 0.30 meter steps.

Left, Front High Left, Center, Front High Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left, Subwoofer

`Specify the distance from each speaker to your listening position.

Note

Speakers that you set to “No” or “None” in

“Speaker Configuration” cannot be selected (page 52).

When the “Powered Zone 2” setting is set to “Yes” and Zone 2 is turned on, the surround back and front high speakers cannot be used.

This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup (page 32).

Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position.

Note

These settings cannot be calibrated in either of the following cases:

The “Audio TV Out” setting is set to “On” (page 64).

HDMI Control(RIHD)” is set to “On” (page 63) and you’re listening through your TV speakers.

The AV receiver is muted.

Left, Front High Left, Center*1, Front High Right,

Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left

`–12dBto 0dB to +12dB in 1 dB steps.

Subwoofer*1

`–15dBto 0dB to +12dB in 1 dB steps.

Note

Speakers that you set to “No” or “None” in

“Speaker Configuration” cannot be selected (page 52).

When the “Powered Zone 2” setting is set to “Yes” and Zone 2 is turned on, the surround back and front high speakers cannot be used.

The test tone is output at the standard level for THX, which is 0 dB (absolute volume setting 82). If you normally listen at volume settings below this, be careful because the test tone will be much louder.

*1 For the center speaker and subwoofer, the level settings made by using the Quick Setup are saved in this menu (page 46).

Tip

If you’re using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading.

En-53

Page 53
Image 53
Onkyo HT-RC470 instruction manual En-53, Speaker Distance Level Calibration

HT-RC470 specifications

The Onkyo HT-RC470 is a powerful AV receiver designed to enhance your home theater experience with cutting-edge technologies and impressive audio performance. This model is a part of Onkyo's renowned lineup and showcases a blend of features that cater to both casual listeners and audiophiles.

At the heart of the HT-RC470 is its robust 7.2-channel amplification system, delivering an impressive 100 watts per channel. This ensures that your audio experiences are rich and immersive, with clear dialogue and dynamic soundscapes across various genres. The receiver supports high-resolution audio formats, allowing music lovers to enjoy every nuance in their favorite tracks.

One of the most notable features of the HT-RC470 is its compatibility with Dolby Atmos and DTS:X. These advanced sound technologies create a three-dimensional listening experience that transports you into the action of movies, games, and music. With object-based sound, audio can move freely around you, adding depth and realism.

The receiver also incorporates the latest HDMI technology, including 4K video pass-through and support for HDCP 2.2, making it future-proof for next-generation content. This ensures seamless connectivity with 4K Ultra HD TVs and other devices, providing stunning picture quality.

Onkyo has integrated several audio calibration technologies in the HT-RC470, such as AccuEQ, which automatically measures and adjusts speaker settings for optimal sound quality based on your room’s acoustics. This feature simplifies setup and ensures that you get the best possible performance with minimal effort.

In terms of connectivity, the HT-RC470 features an array of inputs and outputs, including multiple HDMI ports, optical and coaxial digital audio inputs, and USB connectivity for streaming music from your devices. Built-in Wi-Fi and Bluetooth capabilities allow for easy wireless streaming from your smartphone or tablet, adding to its versatility.

Furthermore, the receiver is app-controllable via Onkyo’s remote app, enabling adjustment of settings and playback from the convenience of your mobile device. This feature is particularly useful for users who prefer a more dynamic control experience.

The Onkyo HT-RC470 embodies a perfect balance of performance, modern features, and user-friendly design, making it a strong choice for anyone looking to enhance their home theater setup and enjoy a truly immersive audio-visual experience. With its thoughtful engineering and array of options, it is built to meet the demands of today’s multimedia environments.