Playing DTS program material, using the pause, fast — forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.
■The beginning of audio received by an HDMI IN can’t be heard
Since it takes longer to identify the format of an | — |
HDMI signal than it does for other digital audio |
|
signals, audio output may not start immediately. |
|
■There’s no sound during Whole House Mode
Make sure you’ve selected an analog audio input. | 51 |
Video
■ There’s no picture
Make sure that all video connecting plugs are pushed | 14 |
in all the way. |
|
|
|
Make sure that each video component is properly | 15, 16 |
connected. |
|
If your TV is connected to the HDMI output(s), select | 50 |
“- - - - |
|
composite video, and component video sources. |
|
|
|
If the video source is connected to a component video | 16, 51 |
input, you must assign that input to an input selector, |
|
and your TV must be connected to either the HDMI |
|
output(s) or COMPONENT VIDEO OUT. |
|
If the video source is connected to a composite video | 16 |
input, your TV must be connected to the HDMI |
|
output(s) or the corresponding composite video |
|
output. |
|
|
|
If the video source is connected to an HDMI input, | 15, 50 |
you must assign that input to an input selector, and |
|
your TV must be connected to the HDMI output(s). |
|
On your TV, make sure that the video input to which | — |
the AV receiver is connected is selected. |
|
■There’s no picture from a source connected to an HDMI IN
Reliable operation with an | 92 |
not guaranteed. In addition, video signals from a PC |
|
are not guaranteed. |
|
|
|
When the resolution is set to any resolution not | 50 |
supported by the TV, no video is output from the |
|
HDMI outputs. |
|
If the message “Resolution Error” appears on the | — |
AV receiver’s display, this indicates that your TV |
|
does not support the current video resolution and you |
|
need to select another resolution on your DVD |
|
player. |
|
■ The on-screen menus don’t appear
On your TV, make sure that the video input to which — the AV receiver is connected is selected.
When the AV receiver is not connected to a TV via — HDMI OUT MAIN,
■The on-screen display does not appear
Depending on the input signal, the
is output to a device connected to HDMI OUT MAIN.
Tuner
■Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light
Relocate your antenna. | — |
Move the AV receiver away from your TV or | — |
computer. |
|
Listen to the station in mono. | 30 |
|
|
When listening to an AM station, operating the | — |
remote controller may cause noise. |
|
Passing cars and airplanes can cause interference. | — |
|
|
Concrete walls weaken radio signals. | — |
If nothing improves the reception, install an outdoor | — |
antenna. |
|
En-79
Appendix
Remote Controller
■ The remote controller doesn’t work
Before operating this unit, be sure to press | — |
RECEIVER. |
|
|
|
Make sure that the batteries are installed with the | 4 |
correct polarity. |
|
Install new batteries. Don’t mix different types of | 4 |
batteries, or old and new batteries. |
|
|
|
Make sure that the remote controller is not too far | 4 |
away from the AV receiver, and that there’s no |
|
obstruction between the remote controller and the AV |
|
receiver’s remote control sensor. |
|
Make sure that the AV receiver is not subjected to | — |
direct sunshine or |
|
Relocate if necessary. |
|
|
|
If the AV receiver is installed in a rack or cabinet | — |
with |
|
not work reliably when the doors are closed. |
|
Make sure you’ve selected the correct remote | 10, 74 |
controller mode. |
|
|
|
When using the remote controller to control other | — |
manufacturers’ AV components, some buttons may |
|
not work as expected. |
|
Make sure you’ve entered the correct remote control | 73 |
code. |
|
|
|
Make sure to set the same ID on both the AV receiver | 66 |
and remote controller. |
|
|
|
■ Can’t control other components
If it’s an Onkyo component, make sure that the u 17 cable and analog audio cable are connected properly. Connecting only an ucable won’t be enough.
Make sure you’ve selected the correct remote | 10, 74 |
controller mode. |
|
If you’ve connected an cassette tape deck to the | 43 |
TV/CD IN jack, or an RI Dock to the TV/CD IN or GAME IN jacks, for the remote controller to work properly, you must set the input display appropriately.