Troubleshooting, Symptom Cause | Onkyo R-801A specs

Troubleshooting

If you have any problems with the unit, please check the troubleshooting table below ﬁrst. For any problems not covered in the table, please consult your nearest ONKYO authorized service center.

Symptom

Cause

Remedy

The unit doesn’t turn	• The AC power cord is not fully
on.	inserted into the wall outlet.

•Insert the AC power cord (mains lead) plug into the wall outlet (the mains) securely.

Sound is reproduced from neither left or right speaker.

•The wire of the speaker cord is touching the other jacks, con- nectors, or metal parts.

•The volume level is turned down to the minimum.

•The sound is muted with the muting function.

•The headphones are connected to the PHONES jack.

•The audio signal is not being input from the connected CD player or MD recorder.

•Timer recording is in process.

•Check the speaker connections (see page 16).

•Adjust the volume level (see page 27).

•Press MUTING button on the remote controller to restore the sound (see page 29).

•Turn down the volume level ﬁrst, then disconnect the head- phones. Then, readjust the vol- ume level.

•Check the connected CD player or MD recorder.

•During timer recording, the sound is muted. If you wish to listen to the sound, press the MUTING button on the remote controller to cancel mute.

Sound is reproduced • The speaker cord is not con-

from only one speaker. nected properly or ﬁrmly, or is disconnected.

•Check the speaker connections (see page 16).

No sound is repro- duced when the (wake-up) timer oper- ates.

•The volume level is turned • Adjust the volume to the proper

down to the minimum.	level when you set the timer
	(see page 27).

The remote control •	The batteries in the remote
doesn’t operate.	controller are dead.
•	The remote controller is out of
	the control range.
•	There is some obstruction
	between the remote controller
	and the unit.

•Replace the batteries with new ones (see page 20).

•Operate the remote controller within the control range (see page 20).

•Try to operate the remote con- troller from a different angle, or remove the obstruction.

48

Image 48

Onkyo R-801A instruction manual Troubleshooting, Symptom Cause

Contents

801A Important Safeguards S2898A Precautions For British model For U.S. model FCC Information for UserFor Canadian model Modele pour les Canadien Main Features Supplied accessoriesLow impedance drive discrete output Trol Stage Table of contents Auto Power On Remote Control OperationProgram Timer Sleep Timer Arranging the system components Combination exampleVertical way stacking Connecting to the audio connector Before connecting Connections for combination example Analog Output Connecting the connectors and AC Outlets Connections Connecting audio/video equipment to audio connectors Remote Control OUT OUT CDR/PC Connecting a subwoofer When connecting a subwooferWith a built-in ampliﬁer With no built-in ampliﬁer Connecting the remote control cables Toggling between CD and DVD for the input display Connecting speaker systems Connecting left and right speakersConnecting the speaker cords to the speaker connectors Preparing the speaker cords for connection Connecting the AM antenna Antenna connections Connecting the FM antenna FM indoor antennaFM outdoor antenna Connecting the 300 ohm ribbon wire Connecting the coaxial cableDirectional Iinkage Preparing the remote controller Installing the remote controller batteriesUsing the remote controller Connecting the AC power cord mains lead STANDBY/ON indicator Setting the Clock Setting the clock automatically European models onlyPlug in the power cord Time indicator turns off Timer Conﬁrming/changing the RDS station used by AccuclockEnter Setting the clock manually STANDBY/ON Press the Enter button to conﬁrm the setting Number buttons Use Button Number buttons to set the desiredPress the Enter button Tip While the unit is in Standby/Off mode While the power to the unit is turned onClock Call function Clock Input Volume VolumeChoosing the required source Adjusting the sound Acoustic Presence Muting/Listening with the headphones Listening with the headphonesMuting the sound Muting Muting Recording InputBefore recording Prepare the recording component Tuning the radio Using Auto Memory FM onlyPresetting your favorite stations Receiving stations Tuning in FM stations Tuning in the AM stationsMemory Press the Memory button Selecting preset stations Clearing preset stationsPress the FM Mode button Naming a preset station Naming a preset stationInput √TUNING Display Memory Memory √TUNING Changing the existing charactersSelect the station you wish to modify Press and hold the Display button for a few seconds FM Mode Use the √TUNING / con- trol to change the characterClearing all names stored in memory What is RDS? Receiving RDS European models onlyDisplaying Radio Text RT Display Using the timer Timer buttonTimer setting modes Buttons Changing the Weekday and Weekend settings Press the or button to select Weekend or Weekday Using the timer Programming to play at a speci- ﬁed time Programming to record at a spec- iﬁed time Button to select Switching the timer ON/OFF Press the or button to switch the selected mode on or OFFPress the Enter button to conﬁrm the selection Cancelling the Sleep setting Sleep functionSleep Start playing something you would like to listen to Index to parts and controls Front panelDisplay Acoustic Remote controller AdjustREC Dayset Stereo cassette tape deck control DVD/CD player controlCD player or changer / MD recorder CD recorder control MD recorder control Troubleshooting Symptom Cause RDS function Speciﬁcations Power supply Power consumptionWeight General Clock precision Onkyo U.S.A. Corporation Onkyo Europe Electronics GmbHOnkyo China Limited