Enjoying music or videos with the TX-SR800

SLEEP

 

 

 

 

 

 

DISPLAY

DIMMER

 

 

 

 

 

REC OUT

ZONE 2

OFF

 

MASTER VOLUME

STANDBY/ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SETUP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TUNI NG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

STANDBY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

RETURN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PRESET

 

 

 

 

 

 

ON

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UPSAMPLING

 

 

 

 

DIRECT/PURE AUDIO STEREO

SURROUND

THX

DSP

MEMORY

FM MODE

A-FORM LISTENING MODE MEMORY

 

 

 

PURE AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLEAR

 

 

 

 

 

 

PHONES

 

ZONE 2 (GRN )

 

 

 

 

 

 

 

 

 

 

 

VIDEO 5

 

 

AUDIO

REC

( RED )

DVD

VIDEO 1

VIDEO 2

VIDEO 3

VIDEO 4

VIDEO 5

TAPE

TUNER

PHONO

C D

 

INPUT

 

 

 

SELECTOR

 

 

 

 

 

 

 

 

 

 

 

 

VCR 1

VCR 2

 

 

 

 

 

 

 

DIGITAL

S VIDEO

VIDEO

L AUDIO R

TX-SR800

MUTING

PHONES

Temporarily turning off the sound

To turn off the sound momentarily, press the MUTING button on the remote controller. When pressed, “Muting” is displayed on the TX- SR800. Press the MUTING button again to turn the sound back on.

Remote controller

Adjusting the bass and treble

You can adjust the bass and treble levels at the Setup Menu → Audio Adjust Menu → Tone Control Sub-menu (see page 53). This function only affects the front left and right speakers, center speaker, and subwoofer. Only the bass level can be adjusted for the subwoofer (the treble adjustment is not effective). For multichannel sources, these dials will not work if the tone control is set to “Direct” or “Pure Audio.”

Listening with headphones

To listen with headphones, plug a pair of headphones with a standard stereo plug into the PHONES jack on the TX-SR800 front panel.

When you connect headphones, no sound will be heard from the speakers.

When the headphones are unplugged, the TX-SR800 returns to its original listening mode. When using the headphones, you can only use the Direct, Stereo, and Mono listening modes. (Available modes can vary depending on the current input source.)

If you have selected MULTI CH INPUT, you will only hear the sound only output to the front right and left channels.

The headphone volume level can be adjusted at the Setup Menu (see page 60).

Note:

The signal to the remote zone (Zone 2) will not be affected by whether or not headphones are connected.

 

 

PHONES

ZONE 2 (G

AUDIO

REC ( R

SELECTOR

 

 

 

 

 

Using the sleep time (remote controller only)

The SLEEP button enables you to set the TX-SR800 to turn off automatically after a specified time period. If you press it once, the TX-SR800 will turn off after 90 minutes. Each time it is pressed thereafter, the remaining time until the TX-SR800 turns off decreases by 10 minutes (i.e., from 90 to 80 minutes). While, the sleep function is enabled, you can press the SLEEP button to see how much time is left. If you now press the SLEEP button, the remaining time will be reduced down to the nearest 10 minutes. If it is pressed again, then the remaining time will be decreased by 10 minutes each time it is pressed (e.g., if SLEEP is pressed with the display reading 54 minutes, it will be reduced to 50 minutes. If it is pressed again, it will then be reduced to 40, then 30, and so on). If the SLEEP button is pressed when the time displayed is less than 10 minutes, the sleep function is cancelled.

If you are using the remote zone (Zone 2), it will turn off at the same time as the main zone. If you want to set the sleep function for Zone 2 only, set the sleep function with main zone turned on and then put the main zone into the standby state.

Remote controller

30