Enjoying music or videos with the TX-SR800

DISPLAY DIMMER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RCVR

 

 

 

 

 

 

 

 

DISPLAY

DIMMER

 

 

 

 

 

REC OUT

ZONE 2

OFF

 

MASTER VOLUME

 

 

STANDBY/ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SETUP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TUNING

 

 

 

 

 

CH SEL

TEST

 

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

RETURN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

 

 

STANDBY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PRESET

 

 

 

 

 

 

 

 

ON

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UPSAMPLING

 

 

 

 

DIRECT/PURE AUDIO STEREO

SURROUND

THX

DSP

MEMORY

FM MODE

A-FORM LISTENING MODE MEMORY

 

 

 

LEVEL

/

PURE AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLEAR

 

 

 

 

 

 

PHONES

 

ZONE 2 (GRN )

 

 

 

 

 

 

 

 

 

 

 

VIDEO 5

 

 

 

 

AUDIO

REC

( RED )

DVD

VIDEO 1

VIDEO 2

VIDEO 3

VIDEO 4

VIDEO 5

TAPE

TUNER

PHONO

C D

 

INPUT

 

 

 

 

 

SELECTOR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VCR 1

VCR 2

 

 

 

 

 

 

 

DIGITAL

S VIDEO

VIDEO

L AUDIO R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TX-SR800

Input source buttons

DISPLAY DIMMER

Switching the display

While listening to or watching an input source, you can display the information regarding the type of source and signal being input by pressing the DISPLAY button on the TX-SR800 or the remote controller.

TX-SR800

Remote controller

DISPLAY

 

When an input source other than FM or AM is selected:

Input

Program format*

Input + Listening mode or Multi Ch

*When the input signal is digital audio

The program format is displayed. For example, the display “Dolby D: 3/2.1” shows that the format is Dolby Digital with 5.1 discrete channels consisting of three front channels (front left, front right, and center), two surround channels (surround left and surround right), and the low frequency effect (LFE) channel.

When the front channel number is 2, they are the front left and front right; when it is 1, it is monaural. When the surround channel number is 1, it is monaural; when it is 0, there is no surround channel. When no LFE number is given, there is no LFE channel. Also, if there is no program format for the input signal, nothing will be displayed.

When the input signal is linear PCM

The sampling frequency is displayed. For example, the display “PCM fs: 44.1k” shows that the signal is PCM and that the sampling frequency is 44.1 kHz.

When FM or AM is selected as the input source:

FM/AM frequency +

 

Preset no.

ch

FM/AM +

Listening mode

Adjusting the brightness of the front display

You can adjust the brightness of the front display of the TX-SR800 using the DIMMER button on the remote controller or on the TX- SR800 front panel.

TX-SR800

Remote controller

DIMMER

 

Temporarily changing the speaker output levels

To change the individual speaker volumes temporarily, follow the procedure given below. Each channel can be set between –12 and +12 decibels. The subwoofer can be adjusted between –15 and +12 decibels. Note that the speaker volumes will return to the original settings when the TX-SR800 is put in the standby state.

1. Press the RCVR MODE button.

2. Press the CH SEL button and select the desired speaker.

3. Press the LEVEL or button to adjust the volume level.

Notes:

•You cannot select a speaker if it is set to “No” or “None” in the Speaker Config Sub-menu of the Speaker Setup Menu.

•To have your new speaker levels set here overwrite the settings at Setup Menu → Speaker Setup Menu → Level Calibration Sub-menu, press the TEST button after you complete step 3 in the procedure above.

32