Before using this unit

Setting the voltage selector (Worldwide models only)

Worldwide models are equipped with a voltage selector so that you can set your TX-SR800 to conform with local power supplies. Be sure to set this switch to match the voltage of the power supply in your area before plugging in the unit.

Determine the proper voltage for your area: 220-230 V or 120 V. If the preset voltage is not correct for your area, insert a screwdriver into the groove in the switch and slide the switch all the way to the top (120 V) or bottom (220-230 V), whichever is appropriate.

DIGITAL

 

PRE OUT

 

ANTENNA

AUDIO

VIDEO

S VIDEO

COMPONENT

FRONT SPEAKERS

 

SURR SPEAKERS

 

 

INPUT

 

R

L

 

 

 

 

VIDEO

 

 

 

COAX

FRONT

 

 

 

 

 

 

 

MONITOR

OUTPUT

R

L

 

R

L

 

 

1

 

 

 

 

 

 

 

 

OUT

Y

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION:

 

 

 

 

 

 

 

SUB

 

 

CENTER

 

 

 

 

 

 

SPEAKER

 

 

 

 

AC OUTLETS

 

2

 

 

 

 

 

 

AM

OUT

ZONE 2

P

IMPEDANCE

 

 

 

 

SWITCHED

 

 

 

 

 

 

 

 

R

L

 

 

4 OHMS MIN. OR

 

 

 

 

TOTAL 100W MAX.

 

 

SURR

 

 

 

 

 

 

 

6 OHMS MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

/SPEAKER

 

 

 

 

 

 

3

 

 

 

 

 

 

 

IN

DVD

P

SEE

 

 

 

 

 

 

 

SURR

R

L

 

 

 

 

 

 

 

INSTRUCTION

 

 

 

 

 

 

OPT

BACK/

 

 

 

 

 

 

INPUT 1

MANUAL FOR

 

 

 

 

 

 

1

ZONE 2

 

 

 

 

 

FM

OUT

 

Y

CORRECT

 

 

 

 

 

 

 

 

 

 

 

 

75

 

SETTINGS.

 

 

 

 

 

 

 

R

 

 

L

RAUDIO L

 

 

VIDEO 1

 

VOLTAGE

 

 

 

 

2

FRONT

 

 

MULTI CH

 

 

IN

 

P

 

 

 

 

 

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

 

 

 

SUB

 

 

CENTER

 

 

 

 

VIDEO 2

INPUT 2

SELECTORSURR BACK/

 

 

VOLTAGE

3

 

 

 

 

 

 

PHONO

OUT

 

P

 

 

 

 

 

 

 

 

SURR

 

 

 

 

 

CD

IN

 

Y

CENTER SPEAKER

R

ZONE 2 SPEAKERS

L

SELECTOR

DIGITAL

 

 

 

 

 

 

 

 

I R

 

 

 

 

120V

OUTPUT

 

R

L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT

 

 

 

 

IN

 

 

 

AV RECEIVER

 

OPT

 

 

 

 

 

 

 

IN

VIDEO 3

P

 

 

 

REMOTE

 

MODEL NO. TX-SR800

220-230V

 

SURR

 

 

 

 

 

 

 

 

 

 

 

 

CONTROL

 

 

 

 

BACK

 

 

 

 

 

TAPE

 

 

 

120V

 

 

 

 

 

 

 

GND

 

 

 

R

L

R

L

 

 

OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

VIDEO 4

P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO

 

AUDIO

VIDEO

S VIDEO

 

 

 

 

 

 

 

 

220-230V

Using the remote controller

Point the remote controller toward the remote control sensor. The STANDBY indicator lights up when the unit receives a signal from the remote controller.

Remote control sensor

TX-SR800

STANDBY indicator

30˚

30˚

Approx. 16 feet (5 meters)

Installing the remote controller batteries

1.Remove the battery compartment cover by pressing it and sliding it in the direction shown by the arrow below.

2.Insert two AA (R6 or UM-3) batteries into the battery compartment. Carefully follow the polarity diagram (positive (+) and negative (–) symbols) inside the battery compartment.

3.After the batteries are installed and seated correctly, replace the compartment cover.

1

2

3

Notes:

•Do not mix new batteries with old batteries or different kinds of batteries.

•To avoid corrosion, remove the batteries if the remote controller will not be used for a long time.

•Remove dead batteries immediately to avoid damage from corrosion. If the remote controller does not operate smoothly, remove the old batteries and replace them both with two new AA batteries.

SEND/LEARN indicator

Notes:

•Make sure that the remote control sensor is not subject to strong light such as direct sunlight or inverted fluorescent light for it may prevent proper operation of the remote controller.

•Using another remote controller in the same room or using the TX-SR800 near equipment that uses infrared rays may cause operational interference.

•Do not put objects on the remote controller. Its buttons may be pressed by mistake and drain the batteries.

•Make sure the audio rack doors do not have colored glass. Placing the TX-SR800 behind such doors may prevent proper remote controller operation.

•If there is any obstacle between the remote controller and the remote control sensor, the remote controller will not operate.

7