For further operational instructions, see the pages indicated in brackets [ ].
POWER switch (for all models other than USA and Canadian models) [28]
Press to turn on and off the main power supply for the
•Before turning on the power, check to make sure that all cords are properly connected.
•When the power is turned on, a sudden surge of current will occur that may adversely affect the operation of other devices. To prevent this, do not plug the
STANDBY/ON button [28]
If pressed with the POWER switch turned on (with the receiver plugged in for US models), the
STANDBY indicator [7, 28]
Lights when the
AUDIO SELECTOR button [33]
Press to select the type of audio input signal.
Remote control sensor [7]
DISPLAY button [32]
Press to display information about the current input source signal. Each time you press the DISPLAY button, the screen changes to show you different information concerning the input signal.
DIMMER button [32]
Press to set the brightness of the front display. There are three settings available: normal, dark, and very dark.
•The brightness of the front display can also be performed using the remote controller.
LISTENING MODE buttons [31, 51]
Press these buttons to select a listening mode for the current input source.
DIRECT/PURE AUDIO: Press to switch between the direct and pure audio listening modes.
STEREO: Selects for the stereo listening mode.
SURROUND: Selects for the Dolby Pro LogicII, DTS Neo:6, Dolby Digital, or DTS listening modes.
THX: Selects for the THX listening mode.
DSP /: Switches to the DSP mode.
Front display
MEMORY button [35]
Press to assign the radio station that you are currently tuned into to a preset channel or press to delete a previously preset station.
FM MODE button [34]
Press to change the stereo mode from AUTO to MONO and vice versa. Each time this button is pressed, the AUTO indication turns on and off indicating the current mode. If you are listening to an FM radio station in stereo and the sound cuts out or there is a great deal of noise, switch from AUTO to MONO.
TUNING /, PRESET /, cursor buttons (///) [34, 35, 40]
To tune into a radio station, press the TUNING / buttons. The tuner frequency is displayed in the front display and it can be changed in
When FM is selected as the input source, you can hold down either the TUNING or button and then release it to activate the auto- search feature. It will search for a station in the direction of the button you pressed and stop when it tunes into one. When navigating through the menu settings, these buttons move the cursor up or down (or change the highlighted item).
To select a radio station that was stored using the MEMORY button, press the PRESET / buttons.
When navigating through the menu settings, these buttons select the value or item that you selected with the TUNING / buttons. When you press the SETUP button, the TUNING and PRESET buttons become cursor buttons to be used for Setup Menu operations.
REC OUT/ZONE 2/OFF buttons
These buttons allow you to use the
When either button is pressed, the currently selected input source for recording or outputting to the remote zone is displayed in the front panel display. If “SOURCE” is displayed, then the same input source as that selected for the main zone will be output.
To select an input source, press the desired button (REC OUT or ZONE 2) and then press one of the input source button within 8 seconds. That source will be output for recording or viewing in the remote zone.
To set the output to the source channel, press the desired button (REC OUT or ZONE 2) twice in succession. To turn off the output, press the desired button (REC OUT or ZONE 2) and then press the OFF button within 8 seconds.
Note:
The Rec Out and Zone 2 buttons use the same circuit and therefore cannot be used at the same time. When REC OUT is selected, nothing is output to Zone 2. When ZONE 2 is selected, REC OUT is automatically fixed to SOURCE.
SETUP button [40]
Press to enter the Setup Menu. The OSD Menu will appear on the TV monitor as well as the front display on the
ENTER button [40]
Press to display the screen for the item that is selected in the Setup Menu.
RETURN button [40]
When in the Setup Menu, press to go back one level. If pressed while at the Main Menu, you will exit the Setup Menu.
9