Features
High-Power In-Dash AM/FM Stereo CD Player
Faxback Doc. #
120-2154/55
let you easily adjust high and low sounds
the best possible sound, regardless of the signal level GENERAL
when you drive at night
low volume levels
Page
BEFORE YOU BEGIN THE INSTALLATION
Installation
Which terminal in my vehicles fuse box is for accessories?
How do I connect a wire to the fuse box?
it is mounted
Routing Speaker Wires
Be sure to avoid obstructions behind the mounting surface
Removing the Shipping Screw
Using an Adapter Harness
Black - Ground Red - +12V to Ignition Yellow - +12V to Battery
Connecting Ground, Power, and Optional Components
4 Ohms. Your local RadioShack store carries a full line of speakers
Connecting an Equalizer/Booster
Black - Ground Red - + 12V to Ignition Yellow - + 12V to Battery
Check the equalizer/boosters owners manual for directions
Blue/White - AMP Remote Turn on 500 mA MAX
7. Connect the green wire to the left rear speakers positive terminal
Connecting Two Pairs of Speakers
White - Front Left Speaker + White/Black - Front Left Speaker
Gray - Front Right Speaker + Gray/Black - Front Right Speaker
White - Left Speaker + White/Black - Left Speaker
3. Connect the white wire to the left speakers positive terminal
Gray - Right Speaker + Gray/Black - Right Speaker Green - \
Green/Black - \\ Do Not Connect Violet Violet/Black
2. Disconnect the wire harness and the antenna
TESTING THE CONNECTIONS
the tape while setting 2CH/4CH. Continue with Step
MOUNTING THE STEREO
8. Slide the stereo into the sleeve until it locks into place
7. Reconnect the wire harness and the antenna
REMOVING THE STEREO FROM THE DASH
3. Press RLS to remove the stereos control panel
8. Reconnect the cable to the vehicle batterys negative - terminal
6. Disconnect the wire harness and the antenna
Note The keys are labeled to show their top edges
5. Remove the keys from the slots
USING THE CONTROL PANEL
High-Power In-Dash AM/FM Stereo CD
INSTALLING THE CONTROL PANEL
Player
ADJUSTING THE SOUND
SETTING THE CLOCK 1. Press ON/OFF to turn on the stereo
Operation
BASIC OPERATION TURNING THE STEREO ON AND OFF
number appear
Follow these steps to store an FSM setting
If bAS, TRE, bAL, or FAd and the number disappear before you press
The LOUD button is lit continuously while the stereo is on
1. Repeatedly press FSM until FSM I or FSM II appears
Note FSM I or FSM II blinks while you adjust the controls
DISPLAYING THE CLOCK
While the radio or a CD is playing, press CLOCK to display the clock
MEMORY TUNING
Notes ST appears when an FM signal is received in stereo
Storing Stations
2. Tune to the station you want to store
Selecting a Stored Station
memory
If the stereo could not find any strong stations, P
Scanning Stored Stations
CD PLAYER OPERATION
3. Press + or - to increase or decrease the volume as desired
CAUTIONS Play only CDs that have this mark on them COMPACT D I S C
DIGITAL SOUND
resume play, press CD again
5. To remove a CD from the CD player, press symbol. EJ cd appears
Note If you pause a CD for more then 5 minutes, the stereo turns off
SELECTING A TRACK
SCANNING THE TRACKS
SWITCHING BETWEEN THE CD AND THE RADIO
To begin scanning, press SCN/3. SCN appears during scanning
Indicator
Troubleshooting
Problem
Clean the CD see CD
and Maintenance
High-Power In-Dash AM/FM Stereo
CD Player
Care
CD CARE TIPS
Replacing the Red Power Wires Fuse
REPLACING A FUSE
7. Reconnect the cable to the vehicle batterys negative - terminal
6. If necessary, reinstall the stereo in the dash
3. Grasp the fuses plastic end and pull it out
5. Grasp the new fuses plastic end and push it in
88-108 MHz
Signal-to-Noise S/N Ratio
IF Rejection
Image Rejection
Pick-Up System
Weight
Number of Channels
Error Correction