120-2154/55
High-Power In-Dash AM/FM Stereo CD Player
Features
Faxback Doc. #
low volume levels
the best possible sound, regardless of the signal level GENERAL
let you easily adjust high and low sounds
when you drive at night
Page
How do I connect a wire to the fuse box?
Installation
BEFORE YOU BEGIN THE INSTALLATION
Which terminal in my vehicles fuse box is for accessories?
Removing the Shipping Screw
Routing Speaker Wires
it is mounted
Be sure to avoid obstructions behind the mounting surface
4 Ohms. Your local RadioShack store carries a full line of speakers
Black - Ground Red - +12V to Ignition Yellow - +12V to Battery
Using an Adapter Harness
Connecting Ground, Power, and Optional Components
Blue/White - AMP Remote Turn on 500 mA MAX
Black - Ground Red - + 12V to Ignition Yellow - + 12V to Battery
Connecting an Equalizer/Booster
Check the equalizer/boosters owners manual for directions
Gray - Front Right Speaker + Gray/Black - Front Right Speaker
Connecting Two Pairs of Speakers
7. Connect the green wire to the left rear speakers positive terminal
White - Front Left Speaker + White/Black - Front Left Speaker
Green/Black - \\ Do Not Connect Violet Violet/Black
3. Connect the white wire to the left speakers positive terminal
White - Left Speaker + White/Black - Left Speaker
Gray - Right Speaker + Gray/Black - Right Speaker Green - \
MOUNTING THE STEREO
TESTING THE CONNECTIONS
2. Disconnect the wire harness and the antenna
the tape while setting 2CH/4CH. Continue with Step
3. Press RLS to remove the stereos control panel
7. Reconnect the wire harness and the antenna
8. Slide the stereo into the sleeve until it locks into place
REMOVING THE STEREO FROM THE DASH
5. Remove the keys from the slots
6. Disconnect the wire harness and the antenna
8. Reconnect the cable to the vehicle batterys negative - terminal
Note The keys are labeled to show their top edges
Player
High-Power In-Dash AM/FM Stereo CD
USING THE CONTROL PANEL
INSTALLING THE CONTROL PANEL
BASIC OPERATION TURNING THE STEREO ON AND OFF
SETTING THE CLOCK 1. Press ON/OFF to turn on the stereo
ADJUSTING THE SOUND
Operation
The LOUD button is lit continuously while the stereo is on
Follow these steps to store an FSM setting
number appear
If bAS, TRE, bAL, or FAd and the number disappear before you press
While the radio or a CD is playing, press CLOCK to display the clock
Note FSM I or FSM II blinks while you adjust the controls
1. Repeatedly press FSM until FSM I or FSM II appears
DISPLAYING THE CLOCK
2. Tune to the station you want to store
Notes ST appears when an FM signal is received in stereo
MEMORY TUNING
Storing Stations
Scanning Stored Stations
memory
Selecting a Stored Station
If the stereo could not find any strong stations, P
DIGITAL SOUND
3. Press + or - to increase or decrease the volume as desired
CD PLAYER OPERATION
CAUTIONS Play only CDs that have this mark on them COMPACT D I S C
SELECTING A TRACK
5. To remove a CD from the CD player, press symbol. EJ cd appears
resume play, press CD again
Note If you pause a CD for more then 5 minutes, the stereo turns off
SCANNING THE TRACKS
SWITCHING BETWEEN THE CD AND THE RADIO
To begin scanning, press SCN/3. SCN appears during scanning
Clean the CD see CD
Troubleshooting
Indicator
Problem
Care
High-Power In-Dash AM/FM Stereo
and Maintenance
CD Player
CD CARE TIPS
Replacing the Red Power Wires Fuse
REPLACING A FUSE
5. Grasp the new fuses plastic end and push it in
6. If necessary, reinstall the stereo in the dash
7. Reconnect the cable to the vehicle batterys negative - terminal
3. Grasp the fuses plastic end and pull it out
Image Rejection
Signal-to-Noise S/N Ratio
88-108 MHz
IF Rejection
Error Correction
Weight
Pick-Up System
Number of Channels