4Ω or 8Ω

 

4Ω or 8Ω

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Front and Rear in Tri-mode

 

bridged

 

-

+

-

+

 

bridged

-

+

- +

Figure 4

Figura 4

Abbildung 4

2Ω or 4Ω

2Ω or 4Ω

2Ω or 4Ω

 

2Ω or 4Ω

Tri-mode

For Tri-mode wiring the high frequency speakers should be run in stereo and use a passive in line crossover (capacitor) with each to remove the low frequency.. The mono low frequency speaker would be connected in the bridge mode to the two stereo channels with a in line passive cross- over (inductor) to remove the high frequencies.. The high frequency speakers should be no less than 2 ohms and the low frequency (bridged) speaker should be no less than 4 ohms..

Bridging

For bridging into a single speaker load, the Orion Cobalt CO600..4 has the ability to bridge the front or rear channels together.. The impedance of the speaker must not be less than 4Ω

Amplifier Installation

Choosing Mounting Locations

The location of your amplifier will depend on several important issues.. Due to the low profile size of the Orion Cobalt amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance.. Always mount the amplifier in a place that protects the amplifier from the elements.. In addition, mount the amplifier on a stable, flat surface..

NOTE: Mounting amplifiers upside down is not recommended and may cause premature thermal shutdown..

WARNING! Do not mount any amplifier in the engine compartment.. Amplifiers are not designed to endure the harsh environment of the exterior elements..

Passenger Compartment

If you are going to mount the amplifier in the passenger compartment, make sure you have adequate room for ventilation.. The amplifiers have been designed to make under-seat mount-

© 2007 directed electronics—all rights reserved

7

Page 8
Image 8
Orion G42110 owner manual Amplifier Installation, Tri-mode, Bridging, Choosing Mounting Locations, Passenger Compartment

G42110 specifications

The Orion G42110 is a robust and versatile unmanned aerial vehicle (UAV) designed primarily for a range of commercial and military applications. Renowned for its advanced capabilities, the G42110 integrates state-of-the-art technologies, making it an ideal choice for surveillance, reconnaissance, and various environmental monitoring efforts.

One of the standout features of the Orion G42110 is its impressive flight endurance. With a maximum range of over 1,000 kilometers and the ability to stay aloft for up to 24 hours, this UAV allows for extended missions without the need for frequent refueling or landings. This extended range positions it as an effective tool for long-duration monitoring operations, whether over land or water.

The G42110 is equipped with a high-performance propulsion system that combines a quiet, fuel-efficient engine with cutting-edge aerodynamics. This technology not only enhances the UAV's maneuverability but also reduces its acoustic signature, enabling discreet operations in sensitive areas. The fuselage design contributes to reduced drag and improved operational efficiency, fostering an optimal blend of speed, stability, and stealth.

In terms of payload capacity, the Orion G42110 can accommodate a variety of sensors and equipment, including electro-optical and infrared cameras, synthetic aperture radar (SAR), and signals intelligence (SIGINT) systems. This adaptability allows operators to customize missions to meet specific needs, whether for search and rescue, disaster response, or agricultural monitoring.

The vehicle's avionics suite is equipped with advanced autopilot systems and flight control technologies that facilitate autonomous operation. Pilots can easily program flight paths, allowing for consistent and repeatable missions. Furthermore, real-time data transmission capabilities enable operators to receive immediate situational awareness and quickly make informed decisions in the field.

Durability is another hallmark of the G42110. Built with high-strength composite materials, the UAV is designed to withstand harsh environmental conditions, ensuring reliable performance even in challenging weather scenarios. Its rugged construction enhances its longevity and reduces maintenance costs.

In summary, the Orion G42110 stands out as a versatile UAV that combines long endurance, advanced technologies, and adaptability to various mission profiles. With its exceptional payload capacity, low-observability features, and autonomy, this unmanned aerial vehicle represents a significant advancement in UAV technology, catering to the needs of diverse sectors from military to civilian applications. As industries continue to explore the possibilities of drones, the Orion G42110 is poised to play a pivotal role in modern aerial operations.