ing possible.. When mounting your amplifier under a seat or similar area, keep a minimum of 1" of clearance around the amplifier for adequate cooling..

Trunk Compartment

Mounting your amplifier in the trunk provides excellent performance as long as you do not restrict the airflow around the heatsink of the amplifier.. For optimal results, mount the amplifier with as much clearance as possible.. This type of mounting will yield the best cooling due to the convection effect of the amplifier chassis..

General Precautions and Installation Tips

WARNING! Be careful not to cut or drill into gas tanks, fuel lines, brake lines, hydraulic lines, vacuum lines, or electrical wiring when working on your vehicle..

Disconnect the vehicle's ground wire at the battery before making or breaking connections to the audio system's power supply terminals..

Do not use this amplifier unmounted.. Failing to securely mount the amplifier can result in damage or injury, particularly in the event of an accident.. An unmounted amplifier becomes a dangerous projectile in the event of a crash.. Never mount the amplifier where it might get wet.. Mount the amplifier so the wire connections will not be pulled.. Route the wires where they will not be scraped, pinched or damaged in any fashion..

The +12V power supply wire must be fused as close as possible to the battery terminal, ideally within 18".. Use the recommended fuse size or circuit breaker listed in the Power Connections section of this manual..

If you need to replace the fuse plugged into the side of the amplifier, replace the fuse with the same size ATC / MAXI type fuse that came with the amplifier.. If you are not sure as to the correct value, refer to the Power Connections section of this manual for details.. Using a higher current fuse may result in damage to the amplifier that is not covered under warranty..

NOTE: Make sure all the equipment in the system is turned off when making or breaking con- nections to the input RCAs or speaker terminals.. Turn on the system and slowly turn up the volume control only after double checking all wire connections..

Power for systems with a single amplifier can be supplied by most automotive electrical systems.. Systems with multiple amplifiers may require a higher capacity battery, alternator or the use of a storage capacitor.. We strongly recommend the use of a Directed Audio Essentials power capaci- tor with an extra battery in larger stereo systems..

Orion Cobalt amplifiers generate a certain amount of heat as part of normal operation.. Be sure the area around the amplifier is unobstructed to allow adequate air circulation.. Remember, beach blankets, last week's laundry, school books and homework papers located on top of the amplifier do not improve air flow and may become damaged..

Step By Step Installation

Step 1 Determine the location for the amplifier.. Refer to the Choosing Mounting Locations section of this guide for detailed information..

Step 2 Decide on the system configuration for your amplifier.. For system suggestions, refer to the Speaker Connections section of this guide..

Step 3 Run all the wires from the amplifier location to the speakers, source unit, and bat- tery.. Do not connect the battery at this time.. Be sure to run RCAs and power and speaker wires away from factory electrical wires and system as they pose a great

© 2007 directed electronics—all rights reserved

Page 9
Image 9
Orion G42110 owner manual Trunk Compartment, General Precautions and Installation Tips, Step By Step Installation

G42110 specifications

The Orion G42110 is a robust and versatile unmanned aerial vehicle (UAV) designed primarily for a range of commercial and military applications. Renowned for its advanced capabilities, the G42110 integrates state-of-the-art technologies, making it an ideal choice for surveillance, reconnaissance, and various environmental monitoring efforts.

One of the standout features of the Orion G42110 is its impressive flight endurance. With a maximum range of over 1,000 kilometers and the ability to stay aloft for up to 24 hours, this UAV allows for extended missions without the need for frequent refueling or landings. This extended range positions it as an effective tool for long-duration monitoring operations, whether over land or water.

The G42110 is equipped with a high-performance propulsion system that combines a quiet, fuel-efficient engine with cutting-edge aerodynamics. This technology not only enhances the UAV's maneuverability but also reduces its acoustic signature, enabling discreet operations in sensitive areas. The fuselage design contributes to reduced drag and improved operational efficiency, fostering an optimal blend of speed, stability, and stealth.

In terms of payload capacity, the Orion G42110 can accommodate a variety of sensors and equipment, including electro-optical and infrared cameras, synthetic aperture radar (SAR), and signals intelligence (SIGINT) systems. This adaptability allows operators to customize missions to meet specific needs, whether for search and rescue, disaster response, or agricultural monitoring.

The vehicle's avionics suite is equipped with advanced autopilot systems and flight control technologies that facilitate autonomous operation. Pilots can easily program flight paths, allowing for consistent and repeatable missions. Furthermore, real-time data transmission capabilities enable operators to receive immediate situational awareness and quickly make informed decisions in the field.

Durability is another hallmark of the G42110. Built with high-strength composite materials, the UAV is designed to withstand harsh environmental conditions, ensuring reliable performance even in challenging weather scenarios. Its rugged construction enhances its longevity and reduces maintenance costs.

In summary, the Orion G42110 stands out as a versatile UAV that combines long endurance, advanced technologies, and adaptability to various mission profiles. With its exceptional payload capacity, low-observability features, and autonomy, this unmanned aerial vehicle represents a significant advancement in UAV technology, catering to the needs of diverse sectors from military to civilian applications. As industries continue to explore the possibilities of drones, the Orion G42110 is poised to play a pivotal role in modern aerial operations.