Manuals / OTC Wireless / Computer Equipment / Network Card

OTC Wireless WiSER2400.IP Using the WiSER2400 in a point-to-multiple point link, Scheme

Models: WiSER2400.Plus WiSER2400.IP

1 32

Download 32 pages 6.93 Kb

Page 16

2.2.2Using the WiSER2400 in a point-to-multiple

2.2.2Using the WiSER2400 in a point-to-multiple

point link

Scheme 4

See Figure 8 (overleaf)

Configure each WiSER2400 on the device side to match its serial parameters (baud rate, parity bit, … etc.) with that of the serial device it is to be attached to. Configuration can be done by temporarily connecting the WiSER2400, by a serial cable or wirelessly, to a PC running the WiSER2400 administration software. Similarly, configure the serial parameters of the WiSER2400 on the PC side so that it can communicate with the PC.

Configure the WiSER2400s on either side of the link to match up their UDP/IP settings (listening port, destination IP address, … etc.) for a UDP/IP connection. Enable the WiSER2400 on the PC side to send UDP broadcasts. Enable each WiSER2400 on the device side to receive UDP broadcasts.

Configure the WiSER2400s on both sides to operate in the Ad-hoc mode.

Attach the WiSER2400s to the serial device and the PC. Establish the wireless link between the PC and the WiSER2400. The system is now ready for running the application software on the PC to control the serial devices through the wireless link.

Please refer to Section 3 of this manual for details on configuring the

WiSER2400.

WiSER 2400 Technical Manual

Version 2.16

Copyright  2001-2005, OTC Wireless, Inc. All Rights Reserved

Page 16 of 32

Image 16

OTC Wireless WiSER2400.IP, WiSER2400.Plus Using the WiSER2400 in a point-to-multiple point link, Scheme, See overleaf

Contents

For WiSER2400.IP WiSER2400.Plus 802.11 Wireless Serial Solutions TECHNICAL MANUALTechnical Manual TABLE OF CONTENTS INTRODUCTION Fig. 2 WiSER2400.PlusKey Features SpecificationsInstallation Power1.1.1 Standard Hardware1.1.4 Selecting the Serial Mode for WiSER2400.Plus 1.1.5 Status LEDsProper power is wireless systemDip Switch DB 9 male connectorWiSER2400.Plus 10-pin mini-Phoenix terminal1.2 Installation of WiSER2400 1.3 Installation of VirCOM, the virtualAdministrative Software 1.2.2 Installation2.1 Using the WiSER2400 in a Point-to-point Link 2.1.1 Using the WiSER2400 in a point-to-point link Scheme2. WiSER Deployment Strategies Technical Manual for details on configuring the WiSER2400 and theCopyright  2001-2005, OTC Wireless, Inc. All Rights Reserved WiSER 2400 Technical ManualVersion Page 11 ofSee Figure 6 overleaf 2.1.2 Using the WiSER2400 in a point-to-point link SchemeWiSER2400 Copyright  2001-2005, OTC Wireless, Inc. All Rights Reserved WiSER 2400 Technical ManualVersion Page 13 of2.2 Using the WiSER2400 in a Point-to-multiple point Link 2.2.1 Using the WiSER2400 in a point-to-multiple point linkScheme See Figure 7 overleafCopyright  2001-2005, OTC Wireless, Inc. All Rights Reserved WiSER 2400 Technical ManualVersion Page 15 of2.2.2 Using the WiSER2400 in a point-to-multiple point link SchemeSee Figure 8 overleaf WiSER2400Copyright  2001-2005, OTC Wireless, Inc. All Rights Reserved WiSER 2400 Technical ManualVersion Page 17 of3. Using the WiSER 2400 Administration Software 3.1 Overview3.1.1 The Tabs Fig. 9 WiSER2400 administration connection dialog panelDefaults Baud Rate 9600 / Data bits 8 / Parity none IP address192.168.11.191 Subnet mask3.2 Password Protection The Password Utility is also used to add or change a password for aFig. 12 WiSER2400 Password Utility panel NOTE The default password of WiSER2400 is none. Leave the field blank3.3 Link Status Fig. 13 WiSER2400 administration software Link Status panel3.4 Configuration Page Default value Data Only Mode 3.4.1 Serial PortDefault value 9600 bps Default value noneFig. 15 WiSER2400 administration software 3.4.2 Serial-IP-ProxyConfiguration/Serial-IP-Proxy panel 3.4.3 Wireless Port Default value InfrastructureFig. 16 WiSER2400 administration software Configuration/Wireless Port panelFig. 17 WiSER2400 administration software 3.4.4 Peer HostConfiguration/Peer Host panel 3.5 Encryption 3.5.1 Encryption3.5.2 WEP Keys Creation Fig. 18 WiSER2400 administration software Encryption panel3.6 Statistics 3.6.1 RS232 Statistics3.6.2 WLAN Statistics Fig. 19 WiSER2400 administration software Statistics panelDefault password none leave blank 3.7 AdminFig. 20 WiSER2400 administration software Admin panel Troubleshooting APPENDIXBlank Pages Appear When Opening the Administrative Program Copyright  2001-2005, OTC Wireless, Inc. All Rights ReservedLimited Warranty Recovering from the Data Only ModeCopyright  2001-2005, OTC Wireless, Inc. All Rights Reserved Technical SupportRegulatory Compliance FCC ID MKZ0207232XGCopyright  2001-2005, OTC Wireless, Inc. All Rights Reserved FCC Part 15 Declaration of Conformity DoC