101 | Packard Bell M5801 specification

Item	Description	Item	Description

47ODD_BUTTON_TOP

48ODD_BUTTON_BOTTOM

49SPRING-03

50FRONT-LENS

51HDD_LENS

52BEZEL-FRONT-PANEL

53SWITCH

101

Image 107

Packard Bell M5801 manual 101

Contents

Ixtreme M5801 Service Guide Revision History Date Chapter Updated Copyright Conventions Preface 103 Introduction Introducing the Motherboard Features Integrated I/O Bios FirmwareDimensions and weight Expansion Options Label Component Mainboard Components Cintrusion Block Diagram Icon Component Description Ixtreme M5801 USB ports Connects to USB 2.0 devices USB mouse, USB camera Rear view 1CH Audio Jack Function TableColor/Use Headphone Component Description Port Introduction Speakers System PeripheralsMouse PS/2 or USB, manufacturing option Keyboard PS/2 or USB, manufacturing option Card Reader Option Main Board Major Chips Hardware Specifications and ConfigurationsBios Hotkey List Specification Audio Interface System MemoryCache Memory Video Interface Devices Idle Shut Down Power ManagementIDE Interface USB Port Suspend Mode Power Management Function Acpi support functionDevice Standby Mode Global Standby Mode Entering the Setup Utility Using BiosAbout the Setup Utility Standard Configuration Setup Utility Menus Updating the Bios Item Help Product Information Date and Time Standard Cmos Features Halt On All, But Keyboard UAHCI Port1 /Port2 /Port3 /Port4 /Port5 /Port6A.R.T. Auto Quiet Boot Enabled Advanced Bios FeaturesQuick Boot Enabled UHard Disk Drive Priority Press Enter Removable Device Priority Press Enter USB Beep Message Disabled Boot Up NumLock On Advanced Chipset Features Integrated Peripherals Power On by PCIE/PCI Devices Disabled Power Management SetupDeep Power Off Mode Enabled Power On by RTC Alarm Disabled Restore On AC Power Loss Last State Wake Up by PS/2 KB/Mouse EnabledWake Up by USB KB/Mouse Enabled PC Health Status Smart Fan Enabled Frequency/Voltage Control Enable Clock to All DIMM/PCI EnabledSpread Spectrum Enabled Change Supervisor Password Press Enter Bios Security FeaturesSupervisor Password Not Installed User Password Not Installed Save & Exit Setup Load Default Settings Machine Disassembly and Replacement Before You Begin General Information Removing front bezel and HDD Cage Standard Assembly ProcessOpening the chassis Page Setting the Motherboard Install the PSUPage Page Assembly motherboard Page Insert the ODD/HDD ODD Installed on SATA4 HDD Carrier Installed on SATA3 Master HDD Installed on SATA1 Slave HDD Installed on SATA2 Insert Add-on card Close the Front BezelPage Page Install system fan Overview Removing the Front Bezel Standard Disassembly ProcessOpening the computer Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the Main Board Removing the System FanPage Page Removing the power-supply Removing the HDD in HDD Carrier Page Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Bios Messages Action/FRU Post Error Messages List Specifics about the type and location of the memory error Hard Disk Drive Error Symptoms ListError Symptom Action/FRU Processor / Processor Fan Main board and Memory Audio Error Symptom Action/FRU CD/DVD-ROM Drive Keyboard Error Symptom Action/FRU Video and MonitorPower Supply Parallel/Serial Ports Other Problems Error Symptom Action/FRU Undetermined Problems Choosing a Computer Case Jumper and Connector InformationSafety Precautions Installing the Motherboard in a Case Setting Jumpers Checking Jumper Settings Jumper Type Description Setting Default IIIustration Checking Jumper SettingsJumper Settings Connecting 24-pin power cable Connecting Case Components ATX12V ATX 12V Power Connector Pin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionPwrfan Cooling Fan Power Connector Pin Signal Name Function Pin Signal Name Power Switch Pin Signal Name FunctionPower/Sleep/Message waiting LED Reset Switch Before installing the Processor Installing HardwareInstalling the Processor Following illustration shows CPU installation components CPU Installation Procedure Memory Memory Bus Installing Memory ModulesInstallation Procedure Sata cable optional Sata power cable optional Installing Serial ATA Hard Drives PCIE16X Slot Installing Add-on Cards Onboard PCI interface does not support 64-bit Scsi cards FAUDIO1 Front Panel Audio header Connecting Optional Devices SPDIFOUT1 Spdif out headerOption Sata 1~6 Serial ATA connectors SPIDEBUG1 ChassisPB 30L w/ HDD carrier ME BOM FRU Field Replaceable Unit List Exploded Diagram RAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM 101 102 FRU List