Removing the HDD | Packard Bell M5801 specs

3.6Pull the leaver outwards a little to release the PCI latch then remove the card.

3.7Pull the leaver outwards a little to release the PCI latch then remove other add-on card.

4.Removing the HDD

4.1 Disconnect the screw fixed in the HDD cage.

57

Image 63

Packard Bell M5801 manual Removing the HDD

Contents

Ixtreme M5801 Service Guide Revision History Date Chapter Updated Copyright Conventions Preface 103 Introduction Introducing the Motherboard Features Integrated I/O Bios FirmwareDimensions and weight Expansion Options Label Component Mainboard Components Cintrusion Block Diagram Icon Component Description Ixtreme M5801 USB ports Connects to USB 2.0 devices USB mouse, USB camera Rear view Audio Jack Function Table Color/Use Headphone1CH Component Description Port Introduction Speakers System PeripheralsMouse PS/2 or USB, manufacturing option Keyboard PS/2 or USB, manufacturing option Card Reader Option Main Board Major Chips Hardware Specifications and ConfigurationsBios Hotkey List Specification Audio Interface System MemoryCache Memory Video Interface Devices Idle Shut Down Power ManagementIDE Interface USB Port Suspend Mode Power Management Function Acpi support functionDevice Standby Mode Global Standby Mode Entering the Setup Utility Using BiosAbout the Setup Utility Standard Configuration Setup Utility Menus Updating the Bios Item Help Product Information Date and Time Standard Cmos Features UAHCI Port1 /Port2 /Port3 /Port4 /Port5 /Port6 A.R.T. AutoHalt On All, But Keyboard Advanced Bios Features Quick Boot EnabledQuiet Boot Enabled UHard Disk Drive Priority Press Enter Removable Device Priority Press Enter USB Beep Message Disabled Boot Up NumLock On Advanced Chipset Features Integrated Peripherals Power On by PCIE/PCI Devices Disabled Power Management SetupDeep Power Off Mode Enabled Power On by RTC Alarm Disabled Wake Up by PS/2 KB/Mouse Enabled Wake Up by USB KB/Mouse EnabledRestore On AC Power Loss Last State PC Health Status Smart Fan Enabled Enable Clock to All DIMM/PCI Enabled Spread Spectrum EnabledFrequency/Voltage Control Change Supervisor Password Press Enter Bios Security FeaturesSupervisor Password Not Installed User Password Not Installed Save & Exit Setup Load Default Settings Machine Disassembly and Replacement Before You Begin General Information Standard Assembly Process Opening the chassisRemoving front bezel and HDD Cage Page Setting the Motherboard Install the PSUPage Page Assembly motherboard Page Insert the ODD/HDD ODD Installed on SATA4 HDD Carrier Installed on SATA3 Master HDD Installed on SATA1 Slave HDD Installed on SATA2 Insert Add-on card Close the Front BezelPage Page Install system fan Overview Standard Disassembly Process Opening the computerRemoving the Front Bezel Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the Main Board Removing the System FanPage Page Removing the power-supply Removing the HDD in HDD Carrier Page Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Bios Messages Action/FRU Post Error Messages List Specifics about the type and location of the memory error Hard Disk Drive Error Symptoms ListError Symptom Action/FRU Processor / Processor Fan Main board and Memory Audio Error Symptom Action/FRU CD/DVD-ROM Drive Keyboard Error Symptom Action/FRU Video and MonitorPower Supply Parallel/Serial Ports Other Problems Error Symptom Action/FRU Undetermined Problems Choosing a Computer Case Jumper and Connector InformationSafety Precautions Installing the Motherboard in a Case Setting Jumpers Checking Jumper Settings Checking Jumper Settings Jumper SettingsJumper Type Description Setting Default IIIustration Connecting 24-pin power cable Connecting Case Components ATX12V ATX 12V Power Connector Pin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionPwrfan Cooling Fan Power Connector Pin Signal Name Function Pin Signal Name Power Switch Pin Signal Name FunctionPower/Sleep/Message waiting LED Reset Switch Installing Hardware Installing the ProcessorBefore installing the Processor Following illustration shows CPU installation components CPU Installation Procedure Installing Memory Modules Installation ProcedureMemory Memory Bus Sata cable optional Sata power cable optional Installing Serial ATA Hard Drives PCIE16X Slot Installing Add-on Cards Onboard PCI interface does not support 64-bit Scsi cards FAUDIO1 Front Panel Audio header Connecting Optional Devices SPDIFOUT1 Spdif out headerOption Sata 1~6 Serial ATA connectors SPIDEBUG1 ChassisPB 30L w/ HDD carrier ME BOM FRU Field Replaceable Unit List Exploded Diagram RAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM 101 102 FRU List