Removing the HDD in HDD Carrier | Packard Bell M5801 manual

8.2Disconnect U’s light power cable

9.Removing the HDD in HDD Carrier

9.1 Push HDD carrier button and cover down slowly

9.2 Press orange latch towards the right, open the handle and pull out HDD Carrier

64

Image 70

Packard Bell M5801 manual Removing the HDD in HDD Carrier

Contents

Ixtreme M5801 Service Guide Date Chapter Updated Revision History Copyright Conventions Preface 103 Introducing the Motherboard Introduction Features Expansion Options Bios FirmwareDimensions and weight Integrated I/O Mainboard Components Label Component Cintrusion Block Diagram Ixtreme M5801 Icon Component Description USB ports Connects to USB 2.0 devices USB mouse, USB camera Rear view Color/Use Headphone Audio Jack Function Table1CH Port Introduction Component Description Keyboard PS/2 or USB, manufacturing option System PeripheralsMouse PS/2 or USB, manufacturing option Speakers Card Reader Option Specification Hardware Specifications and ConfigurationsBios Hotkey List Main Board Major Chips Video Interface System MemoryCache Memory Audio Interface USB Port Power ManagementIDE Interface Devices Idle Shut Down Global Standby Mode Power Management Function Acpi support functionDevice Standby Mode Suspend Mode Standard Configuration Using BiosAbout the Setup Utility Entering the Setup Utility Setup Utility Menus Updating the Bios Product Information Item Help Standard Cmos Features Date and Time A.R.T. Auto UAHCI Port1 /Port2 /Port3 /Port4 /Port5 /Port6Halt On All, But Keyboard Quick Boot Enabled Advanced Bios FeaturesQuiet Boot Enabled UHard Disk Drive Priority Press Enter Removable Device Priority Press Enter Boot Up NumLock On USB Beep Message Disabled Advanced Chipset Features Integrated Peripherals Power On by RTC Alarm Disabled Power Management SetupDeep Power Off Mode Enabled Power On by PCIE/PCI Devices Disabled Wake Up by USB KB/Mouse Enabled Wake Up by PS/2 KB/Mouse EnabledRestore On AC Power Loss Last State Smart Fan Enabled PC Health Status Spread Spectrum Enabled Enable Clock to All DIMM/PCI EnabledFrequency/Voltage Control User Password Not Installed Bios Security FeaturesSupervisor Password Not Installed Change Supervisor Password Press Enter Load Default Settings Save & Exit Setup Machine Disassembly and Replacement General Information Before You Begin Opening the chassis Standard Assembly ProcessRemoving front bezel and HDD Cage Page Install the PSU Setting the MotherboardPage Page Assembly motherboard Page Insert the ODD/HDD ODD Installed on SATA4 HDD Carrier Installed on SATA3 Master HDD Installed on SATA1 Slave HDD Installed on SATA2 Close the Front Bezel Insert Add-on cardPage Page Install system fan Overview Opening the computer Standard Disassembly ProcessRemoving the Front Bezel Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the System Fan Removing the Main BoardPage Page Removing the power-supply Removing the HDD in HDD Carrier Page Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Post Error Messages List Bios Messages Action/FRU Specifics about the type and location of the memory error Main board and Memory Error Symptoms ListError Symptom Action/FRU Processor / Processor Fan Hard Disk Drive Error Symptom Action/FRU CD/DVD-ROM Drive Audio Parallel/Serial Ports Error Symptom Action/FRU Video and MonitorPower Supply Keyboard Error Symptom Action/FRU Other Problems Undetermined Problems Installing the Motherboard in a Case Jumper and Connector InformationSafety Precautions Choosing a Computer Case Checking Jumper Settings Setting Jumpers Jumper Settings Checking Jumper SettingsJumper Type Description Setting Default IIIustration Connecting Case Components Connecting 24-pin power cable Pin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionPwrfan Cooling Fan Power Connector Pin Signal Name Function ATX12V ATX 12V Power Connector Pin Signal Name Reset Switch Pin Signal Name FunctionPower/Sleep/Message waiting LED Power Switch Installing the Processor Installing HardwareBefore installing the Processor CPU Installation Procedure Following illustration shows CPU installation components Installation Procedure Installing Memory ModulesMemory Memory Bus Installing Serial ATA Hard Drives Sata cable optional Sata power cable optional Installing Add-on Cards PCIE16X Slot Onboard PCI interface does not support 64-bit Scsi cards Connecting Optional Devices FAUDIO1 Front Panel Audio header Sata 1~6 Serial ATA connectors SPDIFOUT1 Spdif out headerOption SPIDEBUG1 FRU Field Replaceable Unit List Exploded Diagram ChassisPB 30L w/ HDD carrier ME BOM RAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM 101 102 FRU List