Removing the Add-on Card | Packard Bell M5801 instruction

2.2Disconnect the cable housing then you can remove front bezel.

3.Removing the Add-on Card

3.1 Rotate the PCI lock.

3.2 Disconnect the screw fixed in the bracket

55

Image 61

Packard Bell M5801 manual Removing the Add-on Card

Contents

Ixtreme M5801 Service Guide Revision History Date Chapter Updated Copyright Conventions Preface 103 Introduction Introducing the Motherboard Features Dimensions and weight Bios FirmwareExpansion Options Integrated I/O Label Component Mainboard Components Cintrusion Block Diagram Icon Component Description Ixtreme M5801 USB ports Connects to USB 2.0 devices USB mouse, USB camera Rear view Color/Use Headphone Audio Jack Function Table1CH Component Description Port Introduction Mouse PS/2 or USB, manufacturing option System PeripheralsKeyboard PS/2 or USB, manufacturing option Speakers Card Reader Option Bios Hotkey List Hardware Specifications and ConfigurationsSpecification Main Board Major Chips Cache Memory System MemoryVideo Interface Audio Interface IDE Interface Power ManagementUSB Port Devices Idle Shut Down Device Standby Mode Power Management Function Acpi support functionGlobal Standby Mode Suspend Mode About the Setup Utility Using BiosStandard Configuration Entering the Setup Utility Setup Utility Menus Updating the Bios Item Help Product Information Date and Time Standard Cmos Features A.R.T. Auto UAHCI Port1 /Port2 /Port3 /Port4 /Port5 /Port6Halt On All, But Keyboard Quick Boot Enabled Advanced Bios FeaturesQuiet Boot Enabled UHard Disk Drive Priority Press Enter Removable Device Priority Press Enter USB Beep Message Disabled Boot Up NumLock On Advanced Chipset Features Integrated Peripherals Deep Power Off Mode Enabled Power Management SetupPower On by RTC Alarm Disabled Power On by PCIE/PCI Devices Disabled Wake Up by USB KB/Mouse Enabled Wake Up by PS/2 KB/Mouse EnabledRestore On AC Power Loss Last State PC Health Status Smart Fan Enabled Spread Spectrum Enabled Enable Clock to All DIMM/PCI EnabledFrequency/Voltage Control Supervisor Password Not Installed Bios Security FeaturesUser Password Not Installed Change Supervisor Password Press Enter Save & Exit Setup Load Default Settings Machine Disassembly and Replacement Before You Begin General Information Opening the chassis Standard Assembly ProcessRemoving front bezel and HDD Cage Page Setting the Motherboard Install the PSUPage Page Assembly motherboard Page Insert the ODD/HDD ODD Installed on SATA4 HDD Carrier Installed on SATA3 Master HDD Installed on SATA1 Slave HDD Installed on SATA2 Insert Add-on card Close the Front BezelPage Page Install system fan Overview Opening the computer Standard Disassembly ProcessRemoving the Front Bezel Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the Main Board Removing the System FanPage Page Removing the power-supply Removing the HDD in HDD Carrier Page Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Bios Messages Action/FRU Post Error Messages List Specifics about the type and location of the memory error Error Symptom Action/FRU Processor / Processor Fan Error Symptoms ListMain board and Memory Hard Disk Drive Audio Error Symptom Action/FRU CD/DVD-ROM Drive Power Supply Error Symptom Action/FRU Video and MonitorParallel/Serial Ports Keyboard Other Problems Error Symptom Action/FRU Undetermined Problems Safety Precautions Jumper and Connector InformationInstalling the Motherboard in a Case Choosing a Computer Case Setting Jumpers Checking Jumper Settings Jumper Settings Checking Jumper SettingsJumper Type Description Setting Default IIIustration Connecting 24-pin power cable Connecting Case Components Pwrfan Cooling Fan Power Connector Pin Signal Name Function Sysfan Cooling Fan Power Connector Pin Signal Name FunctionPin Signal Name ATX12V ATX 12V Power Connector Pin Signal Name Power/Sleep/Message waiting LED Pin Signal Name FunctionReset Switch Power Switch Installing the Processor Installing HardwareBefore installing the Processor Following illustration shows CPU installation components CPU Installation Procedure Installation Procedure Installing Memory ModulesMemory Memory Bus Sata cable optional Sata power cable optional Installing Serial ATA Hard Drives PCIE16X Slot Installing Add-on Cards Onboard PCI interface does not support 64-bit Scsi cards FAUDIO1 Front Panel Audio header Connecting Optional Devices SPDIFOUT1 Spdif out headerOption Sata 1~6 Serial ATA connectors SPIDEBUG1 ChassisPB 30L w/ HDD carrier ME BOM FRU Field Replaceable Unit List Exploded Diagram RAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM 101 102 FRU List