Skin Tone Detail Skin Tone DTL OFF, on | Panasonic AK-HC1800N

Setting of menu items

MAINTENANCE menu

[7]SKIN TONE DETAIL

SKIN TONE DTL [OFF, ON]

For turning the SKIN TONE DTL ON or OFF.

SKIN GET [OFF, ON]

When ON is selected, the box cursor is output to the screen center. When the image of the subject’s skin is placed inside the box cursor and the ENTER operation is performed,

I CENTER and Q PHASE are set automatically.

SKIN DTL CORING [0 to 7]

For setting the SKIN TONE DTL coring amount.

Y MAX [000 to 255]

For setting the upper limit of the brightness in the skin tone specification area.

Y MIN [000 to 255]

For setting the lower limit of the brightness in the skin tone specification area.

I CENTER [000 to 255]

For setting the phase of the I axis in the skin tone specification area.

I WIDTH [000 to 255]

For setting the phase width of the I axis in the skin tone specification area.

Q WIDTH [000 to 255]

For setting the phase range of the Q axis in the skin tone specification area.

Q PHASE [–128 to +127]

For setting the phase of the Q axis in the skin tone specification area.

- 38 -

Image 38

Panasonic AK-HC1800N operating instructions Skin Tone Detail Skin Tone DTL OFF, on, Skin GET OFF, on

Contents

Operating Instructions Multi Purpose Camera FCC Note Do not Open Indicates safety information Important Safety Instructions Contents Accessories Introduction CharacteristicsBit A/D conversion and brand-new DSP featured New 2/3˝ 2.2 million-pixel CCD is employed H  Precautions for use DON’TS Front view Bottom view Rear view  Lens mount  HD SDI output connector HD SDI OUT Interface cable specifications AK-HC1800N  Tally output connector Tally OUT How to install How to set the lens How to set up the system Configuration example 1 Connection of camera controller Configuration example 2 High-speed P/T system Configuration example 3 High-speed P/T system AW-PH650 Control exercised from the AW-CB400 BAR Procedure for camera menu operation AW-RP655 When the LCD panel is in the pedestal adjustment mode Mode How to set up the system Adjust the black balance Operation procedureAdjust the white balance Start shooting Lens iris gain volume adjustment How to adjustFlange back adjustment for zoom lens Auto iris power zoom lens White balance adjustment Color temperature and white balance adjustment reference Black balance adjustment Gen-lock adjustment Intelligent functions Automatic video level adjustment method Automatic color temperature adjustment method  Using AK-HRP150G camera controller Setting of menu itemsHow to display the menus TOP menu Correctdig OFF, on  Maintenance menuBlack Shading Detection Pedestal -100 to +100 PEDESTAL, GammaPedestal -200 to +200 Gamma DRS OFF, on Gamma OFF, onBlack Gamma OFF, on Cine Gamma Select Video REC, Film REC Flare OFF, on FlareFlare 000 to Knee Point -25.00% to +25.00% KNEE, White Clip When the Knee is set toManual Knee Point Knee Slope Knee Level 100% to 109% White Clip OFF, on KNEE, White ClipKnee OFF, MANUAL, Auto High Color OFF, on Detail Detail OFF, on Knee Aperture OFF, on Detail Slim Detail OFF, on Detail Source Skin Tone Detail Skin Tone DTL OFF, on Skin GET OFF, on Iris Level 000 to Iris Mode LENS, CAMGAIN, Auto Iris Iris PEAK/AVE 000 to Mode S.GAIN1, S.GAIN2, S.GAIN3 Super Gain 35 to 0.75 DRS OFF -10 to +10 DRS on PED Offset -200 to +200 Frame Mode Matrix Matrix Table A, B SAT/PHASE -63 to +63 Color Correction Gain Select Setting menuLighting TUNGSTEN, Daylight LOW, MID, HIGH, S.GAIN1 to Digital Extender OFF Matrix Table OFF, A, BColor Correction OFF, on BAR SEL AWB Active FormatStatus OFF, on AWB OK Menu on BAR OFF, on ABB OKOUT Range RGB Menu SEL Video MENU, Film Menu Shutter Shutter Mode OFF, ON, Synchro Shutter Speed SD-HD Phase CRS -4 to +4 PHASE-COARSE -060 to +060PHASE-FINE -045 to +045 SD-HD Phase Fine -99 to +99 Protocol Protocol 1 to ND-FIL CLEAR, 1/4, 1/16, 1/64 INTELLIGENT1Gain -6dB to 72dB Intelligent MANUAL, AUTO, Lock AGC ATW CLEAR, 1/4, 1/16, 1/64, Auto INTELLIGENT1 Intelligent Mode AGC, ATW, AGC+ATWND Filter Select AGC Speed 1 to INTELLIGENT1 AGC Gain Step NORMAL, MAX HI Light Detect 01 to ATW Speed 1 to Iris Range 1, 2ATW Area 25%, 50%, 90% AGC Mode NORMAL, SPORTS, SN, User The AGC control mode is set here MIX +00dB, +06dB Frame MIX INTELLIGENT1 SUB Menu INTELLIGENT2 Intelligent SET INTELLIGENT2 ATW Width 1 to Iris on Lock LOCK, MANUAL, Panel Camera ID menu LOAD/STORE from Mode LOAD/STOREFile Operation menu Execute Menu list Setting of menu items Maintenance Color SAT/PHASE Correction Setting of menu items Appearance Unit inch mm Specifications Input/output signal Eastern Zone