Black balance adjustment | Panasonic AK-HC1800N manual

How to adjust

Black balance adjustment

Adjust it with the lens closed.

When the motor drive lens is controlled from the camera, adjusting the black balance causes the lens to be automatically closed.

Gen-lock adjustment

When multiple cameras are used or the camera is combined with other equipment, it is necessary to adjust the phase for phase matching by external synchronization.

Horizontal phase adjustment

Observe the waveforms of externally synchronizing signal input (black burst signal) and video signal output by a two-phenomenon oscilloscope, and make the horizontal phase according to the camera menu.

Adjustment with GEN-LOCK of SETTING menu

When HD synchronizing signals are input:

Roughly adjust the synchronizing signal input and video signal output phases by

H PHASE-COARSE.

Finely adjust the synchronizing signal input and video signal output phases by

H PHASE-FINE.

When SD synchronizing signals are input:

Roughly adjust the synchronizing signal input and video signal output phases by

SD-HD PHASE CRS.

Finely adjust the synchronizing signal input and video signal output phases by SD-HD PHASE FINE. If the adjustment performed using SD-HD PHASE is not satisfactory, use H PHASE-COARSE/FINE.

- 25 -

Image 25

Panasonic AK-HC1800N operating instructions Black balance adjustment, Gen-lock adjustment

Contents

Multi Purpose Camera Operating Instructions Do not Open FCC Note Indicates safety information Important Safety Instructions Accessories Contents Bit A/D conversion and brand-new DSP featured CharacteristicsIntroduction New 2/3˝ 2.2 million-pixel CCD is employed H  DON’TS Precautions for use Bottom view Rear view Front view  Lens mount  HD SDI output connector HD SDI OUT AK-HC1800N Interface cable specifications  Tally output connector Tally OUT How to set the lens How to install Configuration example 1 Connection of camera controller How to set up the system Configuration example 2 High-speed P/T system Configuration example 3 High-speed P/T system AW-PH650 BAR Control exercised from the AW-CB400 When the LCD panel is in the pedestal adjustment mode Procedure for camera menu operation AW-RP655 Mode How to set up the system Adjust the white balance Operation procedureAdjust the black balance Start shooting Flange back adjustment for zoom lens How to adjustLens iris gain volume adjustment Auto iris power zoom lens Color temperature and white balance adjustment reference White balance adjustment Gen-lock adjustment Black balance adjustment Intelligent functions Automatic color temperature adjustment method Automatic video level adjustment method How to display the menus Setting of menu items Using AK-HRP150G camera controller TOP menu Black Shading Detection  Maintenance menuCorrectdig OFF, on Pedestal -200 to +200 PEDESTAL, GammaPedestal -100 to +100 Gamma Black Gamma OFF, on Gamma OFF, onDRS OFF, on Cine Gamma Select Video REC, Film REC Flare 000 to FlareFlare OFF, on Manual Knee Point KNEE, White Clip When the Knee is set toKnee Point -25.00% to +25.00% Knee Slope Knee Level 100% to 109% Knee OFF, MANUAL, Auto KNEE, White ClipWhite Clip OFF, on High Color OFF, on Knee Aperture OFF, on Detail Detail OFF, on Detail Source Detail Slim Detail OFF, on Skin GET OFF, on Skin Tone Detail Skin Tone DTL OFF, on GAIN, Auto Iris Iris Mode LENS, CAMIris Level 000 to Iris PEAK/AVE 000 to Super Gain Mode S.GAIN1, S.GAIN2, S.GAIN3 PED Offset -200 to +200 35 to 0.75 DRS OFF -10 to +10 DRS on Matrix Table A, B Frame Mode Matrix Color Correction SAT/PHASE -63 to +63 Lighting TUNGSTEN, Daylight Setting menuGain Select LOW, MID, HIGH, S.GAIN1 to Color Correction OFF, on Matrix Table OFF, A, BDigital Extender OFF BAR SEL Status OFF, on FormatAWB Active AWB OK OUT Range RGB ABB OKMenu on BAR OFF, on Menu SEL Video MENU, Film Menu Shutter Speed Shutter Shutter Mode OFF, ON, Synchro PHASE-FINE -045 to +045 PHASE-COARSE -060 to +060SD-HD Phase CRS -4 to +4 SD-HD Phase Fine -99 to +99 Protocol 1 to Protocol Gain -6dB to 72dB INTELLIGENT1ND-FIL CLEAR, 1/4, 1/16, 1/64 Intelligent MANUAL, AUTO, Lock ATW AGC ND Filter Select INTELLIGENT1 Intelligent Mode AGC, ATW, AGC+ATWCLEAR, 1/4, 1/16, 1/64, Auto AGC Speed 1 to HI Light Detect 01 to INTELLIGENT1 AGC Gain Step NORMAL, MAX ATW Area 25%, 50%, 90% Iris Range 1, 2ATW Speed 1 to NORMAL, SPORTS, SN, User The AGC control mode is set here AGC Mode Frame MIX MIX +00dB, +06dB INTELLIGENT1 SUB Menu INTELLIGENT2 INTELLIGENT2 Intelligent SET Iris on Lock LOCK, MANUAL, Panel ATW Width 1 to Camera ID menu File Operation menu Mode LOAD/STORELOAD/STORE from Execute Menu list Setting of menu items Maintenance Color SAT/PHASE Correction Setting of menu items Unit inch mm Appearance Input/output signal Specifications Eastern Zone