Manuals / Panasonic / Photography / Digital Camera

Panasonic AK-HC1800N operating instructions  Tally output connector Tally OUT

Models: AK-HC1800N

1 70

Download 70 pages 39.24 Kb

Page 12

Major operating controls and their functions

Tally output connector [TALLY OUT]

The R tally and G tally signals are output from this connector.

Pin No.	Signal
1	GND

2	R_TALLY_OUT

3	G_TALLY_OUT

4	+12 V (500 mA Max)

IRIS connector [IRIS]

Used to connect the IRIS control cables of the lens.

Pin No.	Signal	Pin No.	Signal
1	Return control	7	Iris follow
2	VTR-S/S	8	Iris auto selection
3	UNREG GND	9	—
4	Iris manual selection	10	Zoom position information
5	Iris control	11	Focus position information

6	UNREG 12 V	12	NC

Zoom/Focus connector [ZOOM/FOCUS]

Used to connect the zoom/focus control cables of lens.

Pin No.	Signal	Pin No.	Signal
1	Focus control selection	7	COM

2	Zoom control selection	8	Focus control
3	GND	9	Zoom control
4	Forcible iris closing	10	Iris control selection
5	Iris control	11	COM +Voltage
6	+Voltage	12	COM –Voltage

Optional card slot

Slot for inserting an optional card.

Note

This product does not support the optional boards (AK-HHD1500G and AK‑HDC1500G).

- 12 -

Image 12

Panasonic AK-HC1800N operating instructions  Tally output connector Tally OUT

Contents

Operating Instructions Multi Purpose CameraFCC Note Do not OpenIndicates safety information Important Safety Instructions Contents AccessoriesCharacteristics Bit A/D conversion and brand-new DSP featuredIntroduction New 2/3˝ 2.2 million-pixel CCD is employed H Precautions for use DON’TSFront view Bottom view Rear view Lens mount  HD SDI output connector HD SDI OUT Interface cable specifications AK-HC1800N Tally output connector Tally OUT How to install How to set the lensHow to set up the system Configuration example 1 Connection of camera controllerConfiguration example 2 High-speed P/T system Configuration example 3 High-speed P/T system AW-PH650 Control exercised from the AW-CB400 BARProcedure for camera menu operation AW-RP655 When the LCD panel is in the pedestal adjustment modeMode How to set up the system Operation procedure Adjust the white balanceAdjust the black balance Start shootingHow to adjust Flange back adjustment for zoom lensLens iris gain volume adjustment Auto iris power zoom lensWhite balance adjustment Color temperature and white balance adjustment referenceBlack balance adjustment Gen-lock adjustmentIntelligent functions Automatic video level adjustment method Automatic color temperature adjustment methodSetting of menu items How to display the menus Using AK-HRP150G camera controller TOP menu Maintenance menu Black Shading DetectionCorrectdig OFF, on PEDESTAL, Gamma Pedestal -200 to +200Pedestal -100 to +100 GammaGamma OFF, on Black Gamma OFF, onDRS OFF, on Cine Gamma Select Video REC, Film RECFlare Flare 000 toFlare OFF, on KNEE, White Clip When the Knee is set to Manual Knee PointKnee Point -25.00% to +25.00% Knee SlopeKnee Level 100% to 109% KNEE, White Clip Knee OFF, MANUAL, AutoWhite Clip OFF, on High Color OFF, onDetail Detail OFF, on Knee Aperture OFF, onDetail Slim Detail OFF, on Detail SourceSkin Tone Detail Skin Tone DTL OFF, on Skin GET OFF, onIris Mode LENS, CAM GAIN, Auto IrisIris Level 000 to Iris PEAK/AVE 000 toMode S.GAIN1, S.GAIN2, S.GAIN3 Super Gain35 to 0.75 DRS OFF -10 to +10 DRS on PED Offset -200 to +200Frame Mode Matrix Matrix Table A, BSAT/PHASE -63 to +63 Color CorrectionSetting menu Lighting TUNGSTEN, DaylightGain Select LOW, MID, HIGH, S.GAIN1 toMatrix Table OFF, A, B Color Correction OFF, onDigital Extender OFF BAR SELFormat Status OFF, onAWB Active AWB OKABB OK OUT Range RGBMenu on BAR OFF, on Menu SEL Video MENU, Film MenuShutter Shutter Mode OFF, ON, Synchro Shutter SpeedPHASE-COARSE -060 to +060 PHASE-FINE -045 to +045SD-HD Phase CRS -4 to +4 SD-HD Phase Fine -99 to +99Protocol Protocol 1 toINTELLIGENT1 Gain -6dB to 72dBND-FIL CLEAR, 1/4, 1/16, 1/64 Intelligent MANUAL, AUTO, LockAGC ATWINTELLIGENT1 Intelligent Mode AGC, ATW, AGC+ATW ND Filter SelectCLEAR, 1/4, 1/16, 1/64, Auto AGC Speed 1 toINTELLIGENT1 AGC Gain Step NORMAL, MAX HI Light Detect 01 toIris Range 1, 2 ATW Area 25%, 50%, 90%ATW Speed 1 to AGC Mode NORMAL, SPORTS, SN, User The AGC control mode is set hereMIX +00dB, +06dB Frame MIXINTELLIGENT1 SUB Menu INTELLIGENT2 Intelligent SET INTELLIGENT2ATW Width 1 to Iris on Lock LOCK, MANUAL, PanelCamera ID menu Mode LOAD/STORE File Operation menuLOAD/STORE from ExecuteMenu list Setting of menu items Maintenance Color SAT/PHASE Correction Setting of menu items Appearance Unit inch mmSpecifications Input/output signalEastern Zone