REMOTE Specifications (continued)
■Priority of assigned functions
•When both “MARKER1” and “MARKER2” are activated at the same time, “MARKER1” has priority. However, when the display aspect ratio is 4:3, the “MARKER1” aspect ratio is 16:9 and the “MARKER2” aspect ratio is 4:3, “MARKER2” is displayed. In this case, the “MARKER2” background is controlled.
•When “MARKER BACK HALF” and “MARKER BACK BLACK” are activated at the same time, “MARKER BACK BLACK” has priority.
•During GPI edge operation and two or more of “INPUT SEL. VIDEO”, “INPUT SEL. SDI1”, “INPUT SEL. SDI2”, “INPUT SEL. YPBPR/RGB” and “INPUT SEL.
•When “GAMMA SEL. FILM” and “GAMMA SEL. STDIO/PST” are activated at the same time, “GAMMA SEL. FILM” has priority.
RS-232C terminal
The following diagram and the table on the lower right show
| PC Side |
|
| (Straight) | ||||
| Pin number |
| Signal |
|
|
| Pin number | Signal |
|
|
|
|
|
|
|
|
|
| 1 |
| N.C. |
|
|
| 1 | N.C. |
|
|
|
|
|
|
|
|
|
| 2 |
| RXD |
|
|
| 2 | TXD |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 3 |
| TXD |
|
|
| 3 | RXD |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 4 |
| DTR |
|
|
| 4 | DSR |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 5 |
| GND |
|
|
| 5 | GND |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
6 |
| DSR |
|
|
| 6 | DTR | |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| 7 |
| RTS |
|
|
| 7 | CTS |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 8 |
| CTS |
|
|
| 8 | RTS |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 9 |
| N.C. |
|
|
| 9 | N.C. |
|
|
|
|
|
|
|
|
|
RS-232C remote control method
■Connectors and signals Connector: D-SUB 9-pin (female) Signal
Pin number | Signal | Description | |
1 | N.C. | Not connected | |
|
|
|
|
2 | TXD | Transmission data | |
|
|
|
|
3 | RXD | Reception data | |
|
|
|
|
4 | DSR | Connected inside | |
|
|
|
|
5 | GND | Ground | |
|
|
|
|
6 | DTR | Connected inside | |
|
|
|
|
7 | CTS | Connected inside | |
|
|
|
|
8 | RTS | Connected inside | |
|
|
|
|
9 | N.C. | Not connected | |
|
|
|
|
■ Communication parameters | |||
|
|
| |
Signal level |
| ||
|
| ||
Synchro system | Asynchronous | ||
|
|
| |
Transfer rate |
| 9600 bps | |
|
|
| |
Parity |
| None | |
|
|
| |
Data length |
| 8 bit | |
|
|
| |
Stop bit |
| 1 bit | |
|
|
| |
Flow control |
| None | |
|
|
|
|
■Command format
STX (02h) | Command | : | Data | ETX (03h) |
•The command is the
•Append any data after the colon (:) following the command, as required.
■Response formats
1. Setting command response
| STX (02h) | Command |
| ETX (03h) |
2. | Query command response |
| ||
|
|
|
| |
| STX (02h) | Data |
| ETX (03h) |
|
|
|
|
|
3. | Error response |
| ||
|
|
|
| |
| STX (02h) | Error code |
| ETX (03h) |
|
|
|
|
|
| Error codes |
|
|
|
ER001: Invalid command
ER002: Parameter error
49
