Panasonic CF-74GCDADBM 9-9

9-9

Arranging the W-LAN L and R Cable

Attaching the LCD Damper C and LCD Damper D

1. Attach the four LCD Damper C to the upper part and lower part of the LCD Unit.

2. Attach the LCD Damper D to the upper center of the LCD Unit.

W-LAN Antenna L PCB W-LAN Antenna R PCB

LCD Rear Cabnet

Attach the Tape to hold the Cable.

Pass the Cable

through the notch

and lead it downward.

Pass the Cable between

the boss and rib.

Pass the Cable through the notch

and lead it downward.

Lead the Cable along the surface.

ttach the Tape to each of the Cables.

(Avoid overlapping.)

Avoid overlapping of the Cables

(all the way).

Pass the Cable through the notch.

(Avoid running over the ribs.)

Pass the Cable through the notch.

(Avoid running over the ribs.)

A: Match the LCD Damper C by LCD edge 0~2mm

LCD Damper D

LCD Unit

LCD Display SideLCD Rear Side0~1mmLCD Damper C

Match the LCD Damper D to the center

of the LCD Unit.

LCD Damper C

0~1mm

Contents

Main Page LASER SAFETY INFORMATION Page Page CONTENTS 1. Specifications 1-1 Main Specifications 1-2 Main Specifications Wireless LAN <Only for model with wireless LAN> Bluetooth <Only for model with Bluetooth> 1-3 2. Names and Functions of Parts 2-2 EX PC 3 Block Diagram DDR2 SDRAM 18bit XGA Page 4-2 5 Power-On Self Test (Boot Check) Outline of POST 5-1 Error Diagnosis by Checking Beep Signal Sound 6 List of Error Codes <Only when the port replicator is connected> 6-1 6-2 7 Self Diagnosis Test 1 7-1 . Beginning of self-diagnosis test 1-1. Setting of content of setup 2. Operation of PC-Diagnostic Utility 7-2 Page Page 8 Wiring Connection Diagram I O PCB DC-IN PCB SD PCB 8-1 9 Disassembly/Reassembly 9.1. Disassembly Instructions 9.1.1. Preparation 9.1.2. Removing the Battery Pack, the HDD Unit and the DVD-ROM Drive Unit 9.1.3. Removing the HDD 9.1.4. Removing the DIMM Memory Card 9.1.5. Removing the Keyboard 9.1.6. Removing the Speaker and the LED PCB 9-3 9.1.7. Removing the Handle Ass'y 9.1.8. Removing the Bottom Case 9-4 9.1.9. Removing the Wireless Module and MDC Module 9.1.10. Removing the Main PCB 9.1.11. Removing the PC Card Ejector and Lithium Battery 9-5 9.1.12. Removing the DC-IN PCB and I/O PCB 9.1.13. Removing the FAN Motor and SD PCB 9.1.14. Removing the BT PCB 9-6 9.1.15. Removing the USB PCB 9.1.16. Removing the Display unit 9.1.18. Removing the LCD and the Inverter 9.1.17. Removing the LCD Front Cabinet 9-7 9.1.19. Removing the Touch PAD and PAD PCB 9.1.20. Removing the Finger PCB 9-8 9.2. Reassembly Instructions 9.2.1. Attention when CF-74 series is repaired 9.2.2. Setting the Finger PCB 9.2.3. Setting the LCD Unit and the Inverter 9-9 0~1mm LCD Damper C LCD Unit 9-10 S1 9-11 S5 S1 Arranging the TP Power Cable and Attaching the TP/LCD Sheet S2 9-12 9-13 9.2.4. Setting the LCD Front Cabinet 9.2.5. Setting the Display unit 9-14 9.2.6. Setting the USB PCB S2 9-15 9.2.7. Setting the BT PCB. 9.2.8. Setting the SD PCB, Heat Sink and FAN Mo tor 9-16 9-17 9.2.9. Setting the DC-IN PCB and I/O PCB 9-18 9.2.10. Setting the PC Card Ejector and Lithium Battery 9.2.11. Setting the Main PCB S2 9-19 Safety Working FAN Cable Connector (CN28) 9.2.12. Setting the Wireless Module and MDC Module S2 <Preparation for assembly of the MDC Module> Arranging the Modem Cable S1 9.2.13. Setting the Bottom Case 9.2.14. Setting the Handle Ass'y 9-22 9.2.15. Setting the Speaker and the LED PCB S3 9-23 9.2.16. Setting the Keyboard S2 9-24 9.2.17. Setting the DIMM Memory Card and DIMM Cover 9.2.18. Setting the HDD Page 10 Exploded View Screw tightening torque Screw tightening torque a a Replacement Parts List CF-74GCDADBM REF. NO andAREA Page Page Page Replacement Parts List CF-74GCDADBM REF. NO and AREA MAIN PCB ! Page Page Page Page Page Page IO PCB LED PCB USB PCB DC-IN PCB TOUCH SCREEN PCB SD PCB PAD/SWITCH PCB BLUETOOTH PCB