On the unit’s display |
|
|
| Page |
|
|
|
|
|
F99 | ≥ The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch | — | ||
|
| the unit to standby for 3 seconds. Now press [POWER Í/I] on the main unit |
| |
|
| again to turn the unit on. |
| |
|
|
|
|
|
HDMI ONLY | ≥ Some | — | ||
|
|
|
|
|
No PLAY | ≥ There is a viewing restriction on a | 30 | ||
|
|
|
|
|
No READ | ≥ The disc is dirty or badly scratched. The unit cannot play. | — | ||
|
|
|
|
|
PLEASE WAIT | ≥ The unit is carrying out internal process.This is not a malfunction. You cannot | — | ||
|
| operate the unit while “PLEASE WAIT” is displayed. |
| |
|
|
|
|
|
SET | ≥ The remote control and main unit are using different codes. Change the code on | 33 | ||
(“ ” stands for a number.) |
| the remote control. |
| |
|
|
| Press and hold [OK] and the indicated number button at the |
|
|
|
|
| |
|
|
|
| |
|
|
| same time for more than 5 seconds. |
|
|
|
|
| |
|
|
|
|
|
UNFORMAT | ≥ You inserted an unformatted | — | ||
|
| or |
| |
|
|
|
|
|
UNSUPPORT | ≥ You have inserted a disc the unit cannot play. | 6, 7 | ||
|
|
|
|
|
U59 | ≥ The unit is hot. | — | ||
|
| The unit switches to standby for safety reasons. Wait for about 30 minutes until |
| |
|
| the message disappears. |
| |
|
| Select a position with good ventilation when installing the unit. Do not block the |
| |
|
| cooling fan on the rear of the unit. |
| |
|
|
|
|
|
U72 | ≥ The HDMI connection acts unusually. | — | ||
U73 |
| – The connected equipment is not HDMI compatible. |
| |
|
| – Please use HDMI cables that have the HDMI logo (as shown on the cover). |
| |
|
| – The HDMI cable is damaged. |
| |
|
|
|
|
|
Hor F | ≥ There is something unusual. (The service number displayed after H and F | — | ||
|
| depends on the unit’s condition.) |
| |
| ≥ Check the unit using the troubleshooting guide. If the service number does not | |||
|
| disappear, do the following. |
| |
|
| 1)Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it. |
| |
|
| 2)Press [POWER Í/I] to turn the power on. (The unit may be fixed.) |
| |
|
| If the service number does not disappear despite doing the above, request |
| |
|
| service from the dealer. Inform the dealer of the service number when requesting |
| |
|
| service. |
| |
|
|
|
|
|
START | ≥ The system is being restarted during the firmware update. Please do not turn off | 14 | ||
|
| power. |
| |
|
|
|
|
|
UPD/ | ≥ The firmware is being updated. | 14 | ||
|
|
|
|
|
FINISH | ≥ The firmware update is complete. | 14 | ||
|
|
|
|
|
Reference
37
RQT9243 or RQT9350
