Panasonic DMP-BD55, DMP-BD35 Messages, On the television, Connection or router

Messages

The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use.

On the television		Page
Authorization Error	≥ [DivX]: You are trying to play the DivX VOD content that was purchased with a	24
This unit is not authorized	different registration code. You cannot play the content on this unit.
to play this title.
Cannot play.	≥ You inserted an incompatible disc (Discs recorded in PAL video, etc.).	6, 7
Cannot display on this unit.	≥ You tried to play a non-compatible image.	7, 35
	≥ Confirm “SD” on the unit’s display is not blinking and re-insert the card.	—
No disc is inserted.	≥ The disc may be upside down.	—
Rental Expired.	≥ [DivX]: The DivX VOD content has zero remaining plays. You cannot play it.	24
$ This operation is	≥ Some operations are prohibited by the unit or disc. For example;
currently disabled.	– [BD-V]: During play back, reverse slow-motion or reverse frame-by-frame is not	19, 20
	possible.	—
	– Depending on the disc, you may not be able to perform search or skip when
	film previews and warning screens are being played back.
Cannot connect.	≥ When a hub is used but its Link lamp does not light up, check the cable	14
Please check the	connection, LAN terminal connection, cable itself (a cross over cable may be
connection of the LAN	used by mistake), etc.
cable.
IP address is not set.	≥ The “IP Address” in “IP Address/DNS Settings” is “---. ---. ---. ---”. Set the “IP	17
	Address”, “Subnet Mask”, and “Default Gateway”. (Select the automatic address
	acquisition if necessary.)
Cannot obtain IP address	≥ If you use a hub, then check the connection between the hub and the router.
using DHCP.	– Use the UPLINK port of the hub to connect to a router.
Please check the	– Check whether or not the hub’s Link lamp lights up. If it does not light up, then
connection or router	check the cable connection, LAN terminal connection, cable itself (a cross over	14
settings.	cable may be used by mistake), etc.
	≥ If the above conditions are OK, then the router may not operate in DHCP mode.
	Check the router settings and operation. You may reset the router to restore it to
	normal.
This IP address is already in	≥ This unit’s IP address is used by another device. Check the IP addresses of this	—
use.	unit, personal computers, and routers, etc. If necessary, reconfigure them to
Please check the IP address	avoid IP addresses from being duplicated.
setting.
Unable to perform	≥ Turn the unit off. Remove the power cord and reconnect it and try again. If the	—
Connection Test.	same symptom persists, then consult your dealer.
Please try again.
IP address not set correctly.
Connection Test was	≥ If you use a hub, then check the connection between the hub and the router.	14
unsuccessful. No reply	– Use the UPLINK port of the hub to connect to a router.
from host.	– If the hub’s Link lamp does not light up, then check the cable connection, LAN
Please check the	terminal connection, cable itself (a cross over cable may have been used by
connection or router	mistake), etc.
settings.	≥ Check the “IP Address”, “Subnet Mask”, and “Default Gateway” in the “IP	17
	Address/DNS Settings”.	17
	≥ If the MAC address information is required, then press [SETUP] to display the
	“Network” menu.
Network connection	≥ When you set “BD-Live Internet Access” to “Allow (Limited)” and play BD-Live	30
refused.	contents which do not have a content owner certificate, the Internet access of
Please confirm Setup	the content is not allowed. If you allow the content to connect to Internet, set
“BD-Live Internet Access.”	“BD-Live Internet Access” to “Allow (ALL)”.

36

RQT9243 or RQT9350