Messages
The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use.
On the television |
| Page | |
|
|
| |
Authorization Error | ≥ [DivX]: You are trying to play the DivX VOD content that was purchased with a | 26 | |
This unit is not authorized | different registration code. You cannot play the content on this unit. |
| |
to play this title. |
|
| |
Cannot play. | ≥You inserted an incompatible disc (Discs recorded in PAL video, etc.). | 6, 7 | |
Cannot display on this unit. | ≥You tried to play a | 7, 38 | |
| ≥Confirm “SD” on the unit’s display is not blinking and | — | |
No disc is inserted. | ≥The disc may be upside down. | — | |
Rental Expired. | ≥ [DivX]: The DivX VOD content has zero remaining plays. You cannot play it. | 26 | |
$ This operation is not | ≥Some operations are unsupported by the unit. For example; | 20 | |
available. | – |
| |
$ This operation is | ≥Depending on the disc, you may not be able to perform search or skip when film | 20 | |
prohibited by this disc. | previews and warning screens are being played back. |
| |
Cannot connect. | ≥When a hub is used but its Link lamp does not light up, check the cable | 16 | |
Please check the | connection, LAN terminal connection, cable itself (a cross over cable may be |
| |
connection of the LAN | used by mistake), etc. |
| |
cable. |
|
| |
IP address is not set. | ≥The “IP Address” in “IP Address/DNS Settings” is | 17 | |
| Address”, “Subnet Mask”, and “Default Gateway”. (Select the automatic address |
| |
| acquisition if necessary.) |
| |
Cannot obtain IP address | ≥If you use a hub, then check the connection between the hub and the router. | 16 | |
using DHCP. |
| ||
Please check the |
| ||
connection or router | check the cable connection, LAN terminal connection, cable itself (a cross over |
| |
settings. | cable may be used by mistake), etc. |
| |
|
| ||
| ≥If the above conditions are OK, then the router may not operate in DHCP mode. | 16 | |
| Check the router settings and operation. You may reset the router to restore it to |
| |
| normal. |
| |
This IP address is already in | ≥This unit’s IP address is used by another device. Check the IP addresses of this | — | |
use. | unit, personal computers, and routers, etc. If necessary, reconfigure them to |
| |
Please check the IP address | avoid IP addresses from being duplicated. |
| |
setting. |
|
| |
Unable to perform | ≥Turn the unit off. Remove the power cord and reconnect it and try again. If the | — | |
Connection Test. | same symptom persists, then consult your dealer. |
| |
Please try again. |
|
| |
IP address not set correctly. |
|
| |
Connection Test was | ≥If you use a hub, then check the connection between the hub and the router. | 16 | |
unsuccessful. No reply |
| ||
from host. |
| ||
Please check the | terminal connection, cable itself (a cross over cable may have been used by |
| |
connection or router | mistake), etc. |
| |
settings. |
| ||
≥Check the “IP Address”, “Subnet Mask”, and “Default Gateway” in the “IP | 17 | ||
| |||
| Address/DNS Settings”. |
| |
| ≥If the MAC address information is required, then press [SETUP] to display the | 17, 35 | |
| “Network” menu. |
| |
Network connection | ≥When you set | 32 | |
refused. | contents which do not have a content owner certificate, the Internet access of the |
| |
Please confirm Setup | content is not allowed. If you allow the content to connect to Internet, set |
| |
Internet Access” to “Allow (ALL)”. |
| ||
Unable to check for latest | ≥The firmware download server is currently unavailable. Please try again later. | — | |
firmware version. |
|
| |
Please try again later. |
|
| |
High Clarity Sound is | ≥“High Clarity Sound” in setup menu is set to “Enable”, and “High Clarity Sound” in | 31, 33 | |
effective. |
| ||
Analog video output is |
|
| |
turned off when |
|
| |
playback starts. |
|
| |
|
|
|
40
RQT9378
