Panasonic FX-301 manual Amplifier mounting, Bracket Protection seal, Fiber sensor amplifier

FX-301-F

ORDER GUIDE

End plates

End plates are not supplied with the amplifier. Please order it separately when the amplifiers are mounted in cascade.

Appearance	Model No.	Description
		When cascading multiple amplifiers, or when it moves depending
		on the way it is installed on a DIN rail, these end plates ensure
	MS-DIN-E	that all amplifiers are mounted together in a secure and fully
		connected manner.

Two pcs. per set

OPTIONS

Designation	Model No.	Description
Amplifier mounting bracket	MS-DIN-2	Mounting bracket for amplifier
		10 sets of 2 communication window seals and 1 connector seal
		Communication window seal:
Fiber sensor amplifier	FX-MB1	It prevents malfunction due to transmission signal from another
		amplifier, as well as, prevents effect on another amplifier.
protection seal
		Connector seal:
		It prevents contact of any metal, etc., with the pins of the quick-
		connection cable.

Amplifier mounting	Fiber sensor amplifier
bracket	protection seal
• MS-DIN-2	• FX-MB1

SPECIFICATIONS

	Type	NPN output	PNP output
Item	Model No.	FX-301-F	FX-301P-F
Applicable fibers			FD-F7series, FT-F9series
Supply voltage			12 to 24 V DC10 % Ripple P-P 10 % or less

Power consumption		Normal operation: 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage)
		ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
		NPN open-collector transistor	PNP open-collector transistor
		• Maximum sink current: 100 mA (50 mA, if five, or more,	• Maximum source current: 100 mA (50 mA, if five, or
Output		amplifiers are connected in cascade.)	more, amplifiers are connected in cascade.)
		• Applied voltage: 30 V DC or less (between output and 0 V)	• Applied voltage: 30 V DC or less (between output and V)
		• Residual voltage: 1.5 V or less [at 100 mA (50 mA, if five, or	• Residual voltage: 1.5 V or less [at 100 mA (50 mA, if five, or
		more, amplifiers are connected in cascade.) sink current]	more, amplifiers are connected in cascade.) source current]
	Output operation	Leak setting (F7 mode): OFF with detection of leak, Liquid setting (F9 mode): Using the jog switch, choose the signal OFF condition between absence of liquid and presence of liquid.
	Short-circuit protection	Incorporated
Response time		250!s or less (Note 1)
Sensitivity setting		Individual teaching / Collective teaching
Operation indicator		Orange LED (lights up when the output is ON)
Model indicator		Green LED [lights up during liquid setting (F9 mode)]
MODE indicator		RUN: Green LED, TEACH  ALL  ADJ  DISP  OUT: Yellow LED
Digital display		4 digit red LED display
Fine sensitivity adjustment function		Incorporated
Timer function		Delay timer [used only for liquid setting (F9 mode)] (Timer setting selectable from 10 ms, 100 ms, 1,000 ms, and none)
resistance	Ambient temperature	0 to50 C 32 to122 F (If 8 to 16 units are connected in cascade: 0 to45 C 32 to113 F
		(No dew condensation), Storage: 20 to70 C 4 to158 F
	Ambient humidity	35 to 85 % RH, Storage: 35 to 85 % RH
	Ambient illuminance	Sunlight: 10,000 ?x at the light-receiving face, Incandescent light: 3,000 ?x at the light-receiving face
Environmental
	EMC	EN 50081-2, EN 50082-2, EN 60947-5-2
	Voltage withstandability	1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 2)
	Insulation resistance	20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 2)
	Vibration resistance	10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each
	Shock resistance	98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each
Emitting element		Red LED (modulated)
Material		Enclosure: Heat-resistant ABS, Case cover: Polycarbonate, Switch: Acrylic
Connecting method		Connector (Note 3)
Cable extension		Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Weight		20 g approx.

Notes: 1) When detecting leak (output OFF) during leak setting (F7 mode), since the sensor flashes the emitted light, only the response action for turning the signal back to ON is delayed (1 sec. approx.).

2)The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.

3)The cable for amplifier connection is not supplied as an accessory. Make sure to use the optional quick-connection cable given below. Main cable (3-core): CN-73-C1(cable length 1 m 3.281 ft), CN-73-C2(cable length 2 m 6.562 ft), CN-73-C5(cable length 5 m 16.404 ft) Sub cable (1-core): CN-71-C1(cable length 1m 3.281 ft), CN-71-C2(cable length 2 m 6.562 ft), CN-71-C5(cable length 5 m 16.404 ft)

520 08/2005