Display Panel Instructions
Others menu
No. | Item | LCD display | Contents |
| Page |
|
|
|
|
| |
|
|
| Displays the firmware version of the mechanical |
| |
01 | Checking the version | Version | control, | optional |
|
imprinter is not installed, the imprinter version will not |
| ||||
|
|
|
| ||
|
|
| be displayed. |
|
|
|
|
|
|
| |
|
|
| Selects whether the buzzer is turned on or off. If |
| |
|
|
| selection is in the “ON” position: |
|
|
02 | Setting the buzzer | Buzzer | When pressing a key, one short beep will be heard. |
| |
When there is an error, 5 short beeps will be heard. |
| ||||
|
|
|
| ||
|
|
| When scanning is completed correctly, one long beep |
| |
|
|
| will be heard. |
| |
|
|
|
|
| |
03 | Setting the SCSI ID | SCSI ID | Sets the SCSI ID number. |
| |
|
| ||||
|
|
|
|
|
|
|
|
| Sets “Enable” or “Disable”. |
|
|
04 | Setting the terminator | Terminator | “Enable” : If last device on chain. |
|
|
|
|
| “Disable” : If between devices. |
|
|
|
|
|
|
| |
|
|
| • Changes the maximum value of the synchronous |
| |
| Setting the transfer |
| transfer rate of the SCSI interface. |
|
|
05 | Transfer Rate | • Lower the synchronous transfer rate to 10 Mbytes/ |
| ||
rate |
| ||||
|
| sec. if the computer has failed to recognize the |
| ||
|
|
|
| ||
|
|
| scanner or the scanner fails to operate properly. |
| |
|
|
|
|
| |
| Checking the roller |
| The alarm tells you it is time to check the roller. If it is |
| |
| Clean Roller | near 100%, clean the roller. See “Cleaning the Unit” on |
| ||
| cleaning warning |
| |||
06 |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
| Clearing the roller | Clean Roller | Clear the “Clean Roller Warning%” display. |
| |
| cleaning warning |
| |||
|
|
|
|
| |
|
|
|
|
| |
| Checking the roller |
| The alarm tells you the roller needs to be changed. If it |
| |
|
| is near 100%, replace the paper feed roller module and |
| ||
| modules replacement | Replace Roll. |
| ||
| retard roller module. See “Replacing Consumables” on |
| |||
| warning |
|
| ||
07 |
|
|
| ||
|
|
| |||
|
|
|
| ||
| Clearing the roller |
|
|
| |
|
|
|
|
| |
| modules replacement | Replace Roll. | Clear the “Replace Roll. Warning%” display. |
| |
| warning |
|
|
|
|
|
|
|
|
| |
|
|
| Selects the product ID. The product ID setting depends |
| |
08 | Setting the product | Product ID | on the host computer scanner application | you are |
|
ID | using. Allows scanner to emulate other Panasonic |
| |||
|
|
| |||
|
|
| scanners. |
|
|
|
|
|
|
|
|
09 | Setting the sleep | Sleep Mode | Sets the time until sleep mode turns ON. |
|
|
mode |
|
| |||
|
|
|
|
| |
|
|
|
|
|
|
18