( 4 of 6)
NEW Programming Steps
( with reference to the KX-T30810 / 61610 )
Step Program Title Feature Description Default
002 System Password Replaces the PBX Programming Switch
( Installation Manual Page 4 –3 ) * # : System Prog
1234 : Password
008 Operator Assignment Assigns the System Operator Telephone Jack : 01
009 Extension Number Assignment Allows the extension numbering scheme to be changed Jack 01 ( Ext. 201 )
24 ( Ext. 224 )
010 LCD Time Display Selection 12 / 24 hour clock display options 12 HOUR
011 Speed Dial Number Set Used for Speed Dials and Call ID Feature Not stored
012 Alternative Feature Number Plan Replaces feature with a code 50 ~ 59 Not stored
100 Hunt Group Enables Station Hunting for Extension Groups All groups : Disabled
101 Station Hunt Type Assigns Hunting Type for Extension Groups All groups : Terminate
102 Voice Mail Port Enables Jacks ( assigned as Voice Mail Ports )
to send DTMF signalling to Voice Mail Jacks 07 / 08 / 15 / 16 :
Disabled
103 Voice Mail Port
DTMF Integration Enables signalling of Call Status information to
Voice Mail ports ( busy, answered, ringing, etc. ) Disabled
104 Hold Mode Selection Assigns Call Hold Mode for SLT extensions
( Example - HOLD 1 : Recall + on-hook ) HOLD 1
105 Conference Tone Confirmation Tone sent at the Start and End
of a Conference Call Enable ( send )
108 Recall Mode of a Station Locked
Extension Allows locked extensions to send a Recall signal whilst
talking to an external call Disabled ( not allowed )
109 CO Indicator Assignment Allows an extension, not programmed to ring
[408 – 410]
to receive the call by pressing the CO Line button
Enable ( Allow )
110 Recall Key Mode Mode1: Sends Recall signal time ( Prog. Step 418 )
Mode2: Recall signal is sent while the button is pressed Mode 1
111 Hold Music Selection
External Music / Tone Assigns External Music or Tone (Beep) External Music
112 DSS Console Indication Mode
( for FWD / DND ) Assigns if an extension set as FWD/DND
shows as a flashing button on the BLF/ DSS Enable ( Flashing )
115 Extension Ringing Pattern Selection Sets Single / Double / Triple Ring Pattern Single
116 Conference Pattern Selection Set the max. number of parties in a conference 5 party (C-2 E-5)
117 Call Pick-up Tone Confirmation tone sent
when the Call Pickup feature is used Enabled ( Tone )
118 Pulse Restriction Enables / Disables pulses being sent to the CO Line
during a conversation
( when Call Block is set in program step 401 )
Enable
119 Redialling after Pulse / Tone
conversion Allows Redial to use tone dialling on a pulse CO Line
if the call had used * and # to convert to Tone Disable
120 Bell Frequency Sets the Bell Frequency for an SLT device 25 Hz
121 Automatic Line Access Number If set at ‘0’ Operator call becomes ‘9’ Dial 9
122 Auto Rotation of Line Access Auto rotation of CO lines seized Disabled (no rotate)
123 Break Ratio Sets the break ratio to CO lines Mode 1 (66%)
124 SLT Ring Mode Length of SLT Ring Cycle Mode 2 (3 sec)
125 Call Barring Check for * , # Assigns if * and # are checked by the COS program Enable ( Check )
126 DSS Off-Hook Mode Making Intercom call by pressing DSS key Enable
202 Call Forward Start Time Call FWD no answer timer
Options : 5 / 10 / 15 / 20 secs 15 secs
203 Pickup Dial Delay Time
( Hot Telephone ) Auto Dial time delay
Options : 1 / 2 / 3 / 4 secs 3 secs
206 Dial Start Time Time between seizing a CO Line and digits being sent
Range : 0 ~ 1500 milliseconds 0 mS
207 Recall Timing Range Sets the Range for Extensions - SLT Mode 1 (50 ~ 180 mS)
208 Interdigit Time Maximum time allowed between digits when dialling
out. Options : 5 / 10 / 15 secs 20 secs
(Prior to disconnection )
210 DTMF Time Assigns the minimum duration Mode 1 (80 mS)