Manuals / Panasonic / Communications / Answering Machine

Panasonic KX-TG4222 Error messages, Troubleshooting, General use, Useful Information, Problem

Models: KX-TG4221

1 48

Download 48 pages 7.17 Kb

Page 33

Error messages

Useful Information

Error messages

Display message

Busy

Error!!

No link to base. Reconnect main base AC adaptor.

Cause/solution

RThe called unit is in use.

ROther units are in use and the system is busy. Try again later.

RThe handset you are using is too far from the base unit. Move closer and try again.

RThere is no handset registered to the base unit matching the handset number you entered.

RRecording was too short. Try again.

RThe handset has lost communication with the base unit. Move closer to the base unit and try again.

RUnplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again.

RThe handset’s registration may have been canceled. Re-register the handset (page 21).

Troubleshooting

If you still have difficulties after following the instructions in this section, disconnect the base unit’s AC adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset, and then insert the batteries into the handset again.

General use

Problem

The handset does not turn on even after installing charged batteries.

The unit does not work.

Cause/solution

RPlace the handset on the base unit or charger to turn on the handset.

RMake sure the batteries are installed correctly (page 9).

RFully charge the batteries (page 9).

RCheck the connections (page 9).

RUnplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again.

RThe handset has not been registered to the base unit. Register the handset (page 21).

For assistance, please visit http://www.panasonic.com/help

33

Image 33

Panasonic KX-TG4222 Error messages, Troubleshooting, General use, Useful Information, Display message, Cause/solution

Contents

Model No. KX-TG4221 Digital Cordless Answering SystemModel shown is KX-TG4221 Thank you for purchasing a Panasonic productCaller ID Service Table of ContentsVoice Mail Service IntroductionSupplied accessories Accessory informationModel composition IntroductionExpanding your phone system Additional/replacement accessoriesAccessory item IntroductionPower connection For your safetyInstallation Operating safeguardsBattery Important safety instructionsFor best performance Base unit location/avoiding noiseEnvironment Other informationRoutine care Notice for product disposal, transfer, or returnR RF transmission power SpecificationsR Power source R Power consumption Base unitBattery installation Setting upBattery charging Getting StartedIntelligent eco mode Note when setting upDuring a power failure Note for battery installationHandset ControlsBase unit receiver or speaker volume while talkingDisplay Initial settingsDate and time Display language2 MbN “Initial setting” a MOKN 3 MbN “Set tel line” a MOKN Dialing modeGetting Started 1 MMENUNAdjusting the receiver or speaker volume Using the speakerphoneMaking a call using the redial list Pause for PBX/long distance service usersAdjusting the base unit ringer volume Useful features during a callFor call waiting or Call Waiting Caller ID service users Temporary tone dialing for rotary/pulse service usersMaking/Answering Calls Call shareShared Phonebook Shared phonebookAdding entries Finding and calling from a phonebook entryErasing entries Editing entriesChain dial Erasing an entryProgramming Programmable settingsScrolling through the display menus SettingsInitial setting Ph.book settingsRinger settings Ringer volumeOperating additional units Registering a unitRegistering a handset to the base unit Additional handsetsCaller ID Service Using Caller ID serviceCaller ID features Caller listErasing selected caller information Caller ID number auto edit featureErasing all caller information Storing caller information to the phonebookGreeting message Answering systemTurning the answering system on/offListening to messages using the handset Listening to messages using the base unitUsing a pre-recorded greeting message Resetting to a pre-recorded greeting messageRemote operation Remote access codeCalling back Caller ID subscribers only Deactivating remote operationUsing the answering system remotely Answering system settingsRemote commands Voice guidanceCaller’s recording time For voice mail service subscribersAnswering System 1 MMENUNVoice mail service Voice Mail ServiceVoice mail message indication Handset locator IntercomTransferring calls, conference calls Intercom/LocatorUseful Information Wall mountingBase unit B B ATo remove the wall mounting adaptor ChargerUseful Information A A BTroubleshooting Error messagesGeneral use Busy Error No link to base. Reconnect main base AC adaptorBattery recharge Programmable settingsMaking/answering calls, intercom ProblemProblem Caller IDCause/solution ProblemLiquid damage Answering systemProblem Cause/solutionUseful Information FCC and other informationFCC RF Exposure Warning Useful InformationCompatible with Useful InformationHearing Aid T-Coil TIA-1083Instalación Guía Rápida EspañolaGuía Rápida Española Unidad baseCambio de idiomas predeterminado “English” Auricular Sugerencias de operaciónFecha y hora Auricular Operaciones básicasGuía Rápida Española Operaciones básicasCómo hacer y contestar llamadas Auricular r “Ajuste de timbre” s OKPreguntas frecuentes Guía Rápida EspañolaPregunta Causa y soluciónAppendix Customer servicesor, contact us via the web at TTY users hearing or speech impaired users can callLimited Warranty Coverage Warranty For United States and Puerto RicoPanasonic Telephone Products Limited Warranty Ship-In ServiceLimited Warranty Limits And Exclusions When you ship the productAppendix Index Index1 Reconnect AC adaptor to the base unit 4 Read troubleshooting page in the Operating Instructions2 Check if telephone line cord is connected PNQX5754ZA PT1212MU0