1. General
This booklet briefly outlines where and how to install the air conditioning system. Please read over the entire set of instruc- tions for the indoor and outdoor units and make sure all accessory parts listed are with the system before beginning.
1-1. Tools Required for Installation (not supplied)
1. | Standard screwdriver | 6. | Sabre saw or key hole saw | 11. | Tube cutter |
2. | Phillips head screwdriver | 7. | Hacksaw | 12. | Tube flaring tool |
3. | Knife or wire stripper | 8. | Core bits | 13. | Torque wrench |
4. | Tape measure | 9. | Hammer | 14. | Adjustable wrench |
5. | Carpenter’s level | 10. | Drill | 15. | Reamer (for deburring) |
1-2. Accessories Supplied with Unit Table 1
Parts | Figure | Q'ty | Remarks | Parts | Figure | Q'ty | Remarks | |||
Washer |
| 8 | For temporarily |
| 3/16 | 13/32" |
| For | ||
| suspending indoor | Truss head screw | 4 | installation | ||||||
| (5 | 10mm) | ||||||||
|
|
| unit from ceiling |
|
| diagram | ||||
|
|
|
|
|
|
|
| |||
Flare | 1/8"(T3) | 2 | For wide / |
|
|
|
|
| For unit & PVC | |
narrow tube | Drain hose |
|
|
| 1 | |||||
insulation | set | / | tube connection | |||||||
3/16"(T5) | connection |
|
| |||||||
|
| 2 | For wide / |
|
|
|
|
| For drain hose | |
Insulation tape |
| narrow tube / | Hose band |
|
|
| 2 | |||
3/32"(T2) |
|
|
| connection | ||||||
|
| flare nut connection |
|
|
|
|
| |||
|
|
|
|
|
|
|
| |||
|
| 8 | For flare / drain |
|
|
| ||||
Vinyl tie |
| insulating | Tapping screw | 5/32 5/8" |
| 2 |
| |||
|
|
| connection |
| (4 16mm) |
|
|
| ||
Drain hose |
| 1 | For drain tube | Truss head screw | 5/32 | 15/32" | 4 |
| ||
insulation | 13/32"(T10) | connection | (4 | 12mm) |
| |||||
|
|
|
| |||||||
|
|
|
|
|
|
|
| Packed in the | ||
|
|
|
|
|
|
|
|
| ||
Remote |
| 1 |
|
|
|
|
|
| ceiling panel | |
controller |
|
| Special screw | 3/16 | 4 |
| ||||
|
|
|
| |||||||
|
|
|
|
|
|
| ||||
Remote control |
|
|
|
| (5 | 40mm) |
|
| ||
| 1 |
|
|
|
|
|
|
| ||
holder |
|
|
|
|
|
|
|
| ||
|
|
| Use M10 or 3/8" for suspension bolts. |
| ||||||
|
|
|
|
| ||||||
AAA alkaline |
| 2 |
| Suspension bolts and nuts (locally purchased) | ||||||
|
|
|
|
|
|
|
| |||
battery |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
|
| Printed on |
|
|
|
|
|
| ||
installation |
| 1 |
|
|
|
|
|
| ||
| container box |
|
|
|
|
|
| |||
diagram |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
1-3. Optional Copper Tubing Kit
Copper tubing for connecting the outdoor unit to the indoor unit is available in kits which contain the narrow and wide tub- ing, fittings and insulation. Consult your nearest sales outlet or air conditioning workshop.
1-4. Type of Copper Tube and Insulation Material
If you wish to purchase these materials separately from a local source, you will need:
1.Deoxidized annealed copper tube for refrigerant tubing as detailed in Table 2.
Cut each tube to the appropriate lengths 1' to 1'4" (30 cm to 40 cm) to dampen vibration between units.
2.Foamed polyethylene insulation for the specified copper tubes as required to precise length of tubing. Wall thickness of the insulation should be not less than 5/16" (8 mm).
3.Use insulated copper wire for field wiring. Wire size varies with the total length of wiring. Refer to
Table 2
Model | Narrow Tube | Wide Tube | |||
|
|
|
| ||
Outer Dia. | Thickness | Outer Dia. | Thickness | ||
| |||||
|
|
|
|
| |
1/4" (6.35 mm) | 0.0314" (0.8 mm) | 3/8" (9.52 mm) | 0.0314" (0.8 mm) | ||
|
|
|
| ||
|
|
|
|
| |
1/4" (6.35 mm) | 0.0314" (0.8 mm) | 1/2" (12.70 mm) | 0.0314" (0.8 mm) | ||
|
|
|
|
|
CAUTION
Check local electrical codes and regulations before obtaining wire. Also, check any specified instructions or limitations.
4