Indicator | Panasonic VQT0C55 specs

PREPARATION – Selecting the NTSC/PAL signal system –

This unit supports both the NTSC and PAL signal system.

Before inputting analogue signals (composite or YC separate video signals), please select the signal system.

POWER

NTSC

PAL

NTSC/PAL switch

button

indicator

indicator

POWER

OCK HAZARD - DO NOT OPEN.

CHOC ELECTRIQUE - NE PAS OUVRIR.

A.DUB

REC

PLAY

VIDEO

DVCAM

NTSC

PAL REC INH.

I

AG-DV2500

N

1 / 3

9PIN REMOTE

DC

12V

MIC

REMOTE

INPUT

CH

REW

O

AUX

NTSC

PAL

OFF

LINE

2 / 4

STOP

U

AUDIO

T

9PIN WIRELESS

DV S-VIDEO

/4

LINE

S -VIDEO

Steps

1.

2.

Set the unit to the POWER OFF mode.

Please select the signal system with the NTSC/PAL switch on the rear panel.

3. Press the POWER button to engage the POWER ON mode. Either the NTSC or PAL indicator on the front will then light up, according to the NTSC/PAL switch setting.

Memo

•In the playback mode, the signal system of the tape is automatically identified, regardless of the NTSC/PAL switch setting.

•During DV signal input, the signal system of the input signal is automatically identified, regardless of the NTSC/PAL switch setting.

•This unit is equipped with a function to automatically detect the signal system of the cassette being played back or the signal being received at the DV input connector. However, this function may not operate correctly in some instances.

To ensure the correct system selection, it is recommended that you match the rear panel’s NTSC/ PAL switch to the signal system of the input signal or playback tape.

•When the unit enters the STOP mode, the NTSC/PAL switch setting will be engaged.

•If a tape recorded in both NTSC & PAL signal systems is played, the video, audio or time code may be distorted at the position where the signal system is switched.

•When the signal system of the tape and the NTSC/PAL setting differ, video and sound output will be upset for about 5 seconds after playback starts or stops.

•NTSC/PAL signal system conversion is not possible.

E-28

Image 28

Panasonic VQT0C55 manual Preparation Selecting the NTSC/PAL signal system, Indicator

Contents

Digital Video Cassette Recorder VQT0C55 Supplement Port Cable Length For Your Safety Please Read the Following Text Carefully For Continental EUROPE, ETC Wireless remote control DV formatHigh picture and sound quality by digital tech- nology Compatible mechanisms for standard/mini DV cassettes Table of Contents Precautions Introduction Place of storage and use Handling the unit Daily maintenance and regular inspection Regular inspection maintenance Head cleaning Maintenance consultation Precautions on the use of cleaning tape Precautions on the use of tapeCassette tape Memo Over 10 years CondensationPrevention of condensation Power Power button/LED Cassette slotDUB Audio dubbing button/LED Line Remote Remote select switch MIC Microphone input terminalEject Eject button PIN REC Record button/LED FF Fast forward button/LED Play Play button/LEDPause Pause button/LED @ Stop Stop button/LED $ Indicator Audio indicator Sensor for wireless remote controller DC power input terminal 2P NTSC/PAL NTSC/PAL signal se- lection switchPIN Remote 9-pin remote ter- minal D-SUB It cannot be used for NTSC/PAL conversion Audio in Audio input terminal Terminal 4PNal Phono Video OUT S-VIDEO output termi Nal 4P Power button f Still Mode buttonButtons related to menu setting and variable speed playback Display button DUB button Pause button# F. ADV button $ F. REV button On-screen display Contents Method ON-SCREEN Display Regarding on-screen display Content ON-SCREEN DisplayStatus display Memo VTR operation mode ON-SCREEN Display Status displayTime code 00 00 Display at position a Operation in progress Event displayDisplay at position B Display for about 3 seconds Alarm display Copy Inhibit REC InhibitDUB Inhibit REC TAB Preparation Provided wireless remote controller Precautions on the use of batteryGuide on battery replacement When replacing the batteries Using the wireless remote controller Operable scope of the wireless remote controllerSensor for the wireless remote controller Maximum distance to the sensor of the unit 6m Angle Power Connecting to the AC adapterPreparation Screw Switching on the power Turning off the power Preparation Selecting the NTSC/PAL signal system Indicator Loading the cassette Preparation Loading/ejecting cassettesEjecting the cassette Preparation Setting/displaying date and time Setting the date and timeDisplaying the Clock Adjust menu Displaying the top Menu Set the date or time on the Clock Adjust menu To return to the usual menu, do the following Enabling on-screen display Selecting date/time displayTime STYLE...Select the style of time display Connection and setting RecordingConnection Recorder Setting Setting time codes Preset time codesTime code is not preset Time code recording Recording time codes of a DV input terminal Recording index signals Recording method Backup unit the main unit Series recording functionDV Camcorder Set the DV TC DUP. item of the Time Code menu to OFF Audio dubbing Stop ¥ The unit goes into the Still mode ¥ The unit goes into the audio dubbing pause modeHold down the A.DUB button and press the Pause button Press the Pause button Connection/setting Using this unit as a standalone deviceConnecting this unit to a video device with a DV terminal Playback System menu Remote switch on the front panelAUDIO/VIDEO menu Basic playback method Fast forward/rewind Still Mode item of the System menu Special playback functionFrame advance reverse playback Frame reverse in the reverse direction Variable speed playback Set the unit to the search modeChanging the direction of playback Locate function Index searchBlank search Stop mode, press the Blank button Select the output level for audio play- back Playback Selecting playback audio outputMIX Using the unit in an editing system EditLinear editing system Applicable model Play Delay Remote menuREM Stop SEL Synchronization Using the unit in a non-linear system Connecting using DV 1394 terminal Set the Input switch of the front panel to DV Remote switch on the front panel can be set at any position Menu Screen Structure of the menu Setting the menu Set the unit to the Stop modeDisplay the menu for setting Display the top Menu Set the items on the menu To return to the usual screen, do either of the followingPress the button Press the REW button Select page Back Menu Contents of the menus System menu System menu Menu Screen Contents of the menus AUDIO/VIDEO menu Time Code menu Display menu Display menu Audio Info OFF Date StyleTime Style 12HOUR 24HOUR Others Placing the unit in an upright position Others Alarm display Displayed regardless of the Display modeDisplay Status Action Warning display Displayed regardless of the Display mode Loading Failure Troubleshooting Checking the hour meter To set the unit to the Stop modeTo return to the usual screen Specification Diagram of external dimension Unit mm 260 174 Panasonic Broadcast Europe Panasonic Broadcast Europe GmbH