Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic 1082/144 user manual Configuration, Configuring The Hardware Dip Switches

Models: 1082/144 1082

1 32

Page 8

3.0 CONFIGURATION

The Model 1082 and 1082/144 each are equipped with 16 DIP switches that enable conﬁguration of the unit for a wide variety of applications. This section describes switch locations and explains the different conﬁg- urations

3.1 CONFIGURING THE HARDWARE DIP SWITCHES

Using a small ﬂat-tip screwdriver, remove the protective cover located on the underside of the Model 1092 (see Figure 2).

									DSL
									10BT
						Status			Link
					NS		.	G	Model
					703/G		.		Model
				ER .				1194E
	511E			704				1194E
	511E		TMTest		Single
		Modes			Single
511/RDL	511			Mode
511/RDL			Fiber
Normal		-	Fiber
511E/RBL		QuadNetLink
511E/RBL		.G
	703/G10BastT
iDSL704.
mMode

Figure 2. Removing the cover to access DIP switches S1 and S2

Page 8

Image 8

Patton electronic 1082/144 user manual Configuration, Configuring The Hardware Dip Switches

Contents

USER MANUAL MODEL 1082 and 1082/144iDSL Modem with V.34 or X.21 Interface An ISO-9001 Certiﬁed CompanyTABLE OF CONTENTS Warranty InformationConfiguration InstallationModel 1082 Specifications Model 1082C and 1082D Factory Replacement Parts andAccessories Model 1082C and 1082D Interface Pin Assignments1.2 CE NOTICE 1.0 WARRANTY INFORMATION1.1 FCC INFORMATION 1.3 SERVICE Tel 301 E-mail support@patton.com2.2 DESCRIPTION 2.1 FEATURES2.0 GENERAL INFORMATION 2.3 1082 SNMP MANAGEMENT SOLUTIONS HTTP/HTML Managementconnections to remote 1082sFigure 2. Removing the cover to access DIP switches S1 and S2 3.0 CONFIGURATION3.1 CONFIGURING THE HARDWARE DIP SWITCHES Conﬁguring DIP Switch S1 Factory DefaultS1 Summary Table PositionSwitches S1-1 and S1-2 Data Rate Switch S1-3 Data Set Ready during Line Loopback TestSetting S1-1Switch S1-4 Must be set to the ON position Reserved Switch S1-5 Asynchronous/Sync OperationSwitches S1-6 and S1-7 System Clock Mode Switch S1-8 Response to RDL RequestConﬁguring DIP switch S2 S1-8S2 Summary Table SettingSwitches S2-1 19.2 kbps or 144* kbps Synchronous Rate Enable Switch S2-2 Front Panel Switch DisableSwitches S2-3 Response to Local Line Loop Requests from DTE Switches S2-4 and S2-5 Not AssignedSwitch S2-6 Response to RDL Request from DTE Switch S2-7 Compatability ModeSwitch S2-8 Not Assigned S2-74.0 INSTALLATION V.35 connectorPower input connector 4.1 CONNECTING THE TWISTED PAIR INTERFACE4.2 CONNECTING THE MODEL 1082 V.35 SERIAL INTERFACE Connecting the Model 1082 V.35 to a DTE DeviceConnecting the Model 1082 V.35 to a DCE Device DSL Span ModelFigure 7. Connecting the Model 1082 to V.35 serial DCE 4.3 CONNECTING THE MODEL 1082 X.21 SERIAL INTERFACEConnecting the Model 1082 X.21 to a “DCE” or “DTE” Device 15-pin D-Sub cable Opening the CaseStraight-through In this example, the DCE/DTE strap is configured for DTE DB-15 connector4.4 CONNECTING POWER Universal AC Power 100-240VAC+Vin DC PowerTo Power Supply JackTo -48VDC Vin Source 5.1 POWER-UP 5.0 OPERATION5.2 LED STATUS MONITORS DSL Link5.3 TEST MODES Local Line Loopback LLBRemote Digital Loopback RDL Using the V.52 BER test pattern generator A.6 DIAGNOSTICS A.7 LED STATUS INDICATORSAPPENDIX A A.1 TRANSMISSION FORMATA.8 CONNECTORS A.9 POWERA.13 DIMENSIONS A.14 WEIGHTAPPENDIX B Model #MODEL 1082C AND 1082D FACTORY REPLACEMENT PARTS AND ACCESSORIES DescriptionM/34 Female Connector SignalAPPENDIX C V.35 INTERFACED-Sub-15 Female Connector APPENDIX DDTE /DCE Orientation SignalX.21 Interface DB-15 Female Connector DTE /DCE Conﬁguration APPENDIX ESignal MODEL 1082C AND 1082D INTERFACE PIN ASSIGNMENTPage Copyright 2000 Patton Electronics Company All Rights Reserved