Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic 1082/144 user manual Service, Tel 301 E-mail support@patton.com

Models: 1082/144 1082

1 32

Page 5

1.3 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materi- als Authorization number on the outside of the shipping container. This number may be obtained from Patton Electronics Technical Service at:

Tel: (301) 975-1007

E-mail:support@patton.com

URL: www.patton.com

Note Packages received without an RMA number will not be accepted.

Patton Electronics’ technical staff is also available to answer any ques- tions that might arise concerning the installation or use of your Model 1082 or Model 1082/144. Technical Service hours: 8AM to 5PM EST, Monday through Friday.

Page 5

Image 5

Patton electronic 1082/144 user manual Service, Tel 301 E-mail support@patton.com

Contents

MODEL 1082 and 1082/144 USER MANUALiDSL Modem with V.34 or X.21 Interface An ISO-9001 Certiﬁed CompanyWarranty Information TABLE OF CONTENTSConfiguration InstallationModel 1082C and 1082D Factory Replacement Parts and Model 1082 SpecificationsAccessories Model 1082C and 1082D Interface Pin Assignments1.2 CE NOTICE 1.0 WARRANTY INFORMATION1.1 FCC INFORMATION Tel 301 E-mail support@patton.com 1.3 SERVICE2.2 DESCRIPTION 2.1 FEATURES2.0 GENERAL INFORMATION HTTP/HTML Management 2.3 1082 SNMP MANAGEMENT SOLUTIONSconnections to remote 1082sFigure 2. Removing the cover to access DIP switches S1 and S2 3.0 CONFIGURATION3.1 CONFIGURING THE HARDWARE DIP SWITCHES Factory Default Conﬁguring DIP Switch S1S1 Summary Table PositionSwitch S1-3 Data Set Ready during Line Loopback Test Switches S1-1 and S1-2 Data RateSetting S1-1Switch S1-5 Asynchronous/Sync Operation Switch S1-4 Must be set to the ON position ReservedSwitches S1-6 and S1-7 System Clock Mode Clock ModeS1-8 Conﬁguring DIP switch S2S2 Summary Table SettingSwitch S2-2 Front Panel Switch Disable Switches S2-1 19.2 kbps or 144* kbps Synchronous Rate EnableSwitches S2-3 Response to Local Line Loop Requests from DTE Switches S2-4 and S2-5 Not AssignedSwitch S2-7 Compatability Mode Switch S2-6 Response to RDL Request from DTESwitch S2-8 Not Assigned S2-7V.35 connector 4.0 INSTALLATIONPower input connector 4.1 CONNECTING THE TWISTED PAIR INTERFACEConnecting the Model 1082 V.35 to a DTE Device 4.2 CONNECTING THE MODEL 1082 V.35 SERIAL INTERFACEConnecting the Model 1082 V.35 to a DCE Device DSL Span ModelFigure 7. Connecting the Model 1082 to V.35 serial DCE 4.3 CONNECTING THE MODEL 1082 X.21 SERIAL INTERFACEConnecting the Model 1082 X.21 to a “DCE” or “DTE” Device 15-pin D-Sub cable Opening the CaseStraight-through DB-15 connector In this example, the DCE/DTE strap is configured for DTE4.4 CONNECTING POWER Universal AC Power 100-240VAC+Vin DC PowerTo Power Supply JackTo -48VDC Vin Source 5.0 OPERATION 5.1 POWER-UP5.2 LED STATUS MONITORS DSL LinkLocal Line Loopback LLB 5.3 TEST MODESRemote Digital Loopback RDL Using the V.52 BER test pattern generator A.7 LED STATUS INDICATORS A.6 DIAGNOSTICSAPPENDIX A A.1 TRANSMISSION FORMATA.9 POWER A.8 CONNECTORSA.10 TEMPERATURE RANGE A.13 DIMENSIONSModel # APPENDIX BMODEL 1082C AND 1082D FACTORY REPLACEMENT PARTS AND ACCESSORIES DescriptionSignal M/34 Female ConnectorAPPENDIX C V.35 INTERFACEAPPENDIX D D-Sub-15 Female ConnectorDTE /DCE Orientation SignalAPPENDIX E X.21 Interface DB-15 Female Connector DTE /DCE ConﬁgurationSignal MODEL 1082C AND 1082D INTERFACE PIN ASSIGNMENTPage Copyright 2000 Patton Electronics Company All Rights Reserved