Wiring S-EIDC-UDoor Components, S-Eidc-U | Pelco c3653m-a specs

Wiring S-EIDC-U Door Components

Chapter 2: S-EIDC-U (ethernet Integrated Door Controller)

Wiring S-EIDC-U Door Components

Up to 750 mA of power is provided through the S-EIDC-U for peripheral devices. An illustration of wiring an S-EIDC-U for a single door, and the steps necessary to do so, are as follows:

Optional

S-PCON-U

Power Connector

To Ethernet Hub

Ethernet

ConnectionBuilt-in

Infrared Tamper

Note: Maglock is required to have additional external UL listed power supply.

Door Strike

Door Contact

Card Reader

or Keypad

To Reader LED Output

Output 1

Output 2

Input 1

Common

Input 2

Card Reader

IN

Power

Output 1

Output 3 - NC

Common

Output 3 - NO

Input 3

Common

Input 4

Card Reader

OUT

Power

Output 2

Electro-magnetic

Lock

Card Reader

or Keypad

Optional External

Power Supply

24 vDC, 1 Amp

24V DC IN

Built-in

Warning Buzzer

Reader LED Output

Reader Buzzer Output

S-EIDC-U

CAT 5/6

To Ethernet Hub

(PoE Switch)

Note: The S-EIDC-U device and its UL listed Power Supply must be installed within the protected area (locked area) of the access facility to meet UL requirements.

Note: To meet UL requirements, listed panic hardware must be used to allow emergency exit from the protected area.

Built-in Warning Buzzer

S-EIDC-U Door Component Wiring

Intelli-M Hardware Installation And Reference Guide

13

Image 13

Pelco c3653m-a manual Wiring S-EIDC-UDoor Components, S-Eidc-U, S-EIDC-UDoor Component Wiring

Contents

Pelco, Inc. Worldwide Headquarters Hardware Installation And ReferenceC3653M-A11/08 Trademarks Preface Table of Contents Recessed Mounting Box Official Notices UL Compliance S-EIDC-U, S-PCON-UFCC Declaration Of Conformity S-EIDC-U, S-PCON-U Official Notices Intelli-MHardware Overview Using This Manual Chapter 1 Intelli-M Hardware Overview Contents S-EIDC-U Intelli-MHardware Overview Chapter 1 Intelli-MHardware Overview Using This Manual Chapter 1 Intelli-MHardware Overview Chapter 2 S-EIDC-U ethernet Integrated Door Controller Contents S-EIDC-UOverview Technical Features S-EIDC-UDoor Component Wiring Wiring S-EIDC-UDoor ComponentsS-EIDC-U Step 3 Wire the readers Step 2: Wire the status, shunt, and exit inputsKeep in mind the following points Keep in mind the following points Four Power Options Powering Up An S-EIDC-U Determining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP Addressing Setting A DHCP IP Address Within The S-EIDC-U Quick Mount Assembly Resetting An S-EIDC-UQuick Mount Assembly Breakdown Page Wiring And Powering Up S-PCON-U Chapter 3 S-PCON-U Power Connector ContentsS-PCON-UOverview S-PCON-UOverview Technical Features S-PCON-UWiring and Powering up Diagram Wiring And Powering Up S-PCON-U Chapter 3 S-PCON-UPower Connector Contents Chapter 4 Wiring Connections And ConfigurationsSample S-EIDC-UGlobal Configuration S-EIDC-UWiring Terminals Chapter 4 Wiring Connections And Configurations Sample S-EIDC-UGlobal ConfigurationS-EIDC-U S-EIDC-UWiring Terminals S-EIDC-U Single Door Door Configuration With S-EIDC-U Contents Appendix A eFamily Update UtilityInstalling The eFamily Update Utility eFamily Update Procedure 2.Launch double click the “setup.exe” file Installing The eFamily Update UtilitySupervisor Plus Users Web Interface Users 6.Click the “Close” button Before Updating Your eFamily Device eFamily Update Procedure Figure A-5 Connection Information Screen Figure A-6 Choice To Backup ScreenFigure A-7 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-13 Update Complete Screen Figure A-12 Update In Process Screen Figure A-14 Example Error Message Errors That Occur During UpdatePage Defaults Appendix B Demo Kit WiringInput Configuration Output Configuration Access Service Configuration Controller ConfigurationAlarm Service Configuration Dimensions S-EIDC-UTechnical SpecificationsQuick Mount Assembly Kit Enclosure Ethernet Integrated Door Controller Communication PowerReader Ports Inputs Operational S-PCON-UTechnical Specifications Power ControllerDimensions Power Connector Module S-PCON-U DC Power --24 VDC, 1A Power InPower Out DC Power --22.9 to 24 VDC, 1A Performance Communications Server Requirements Miscellaneous Computer Hardware SpecificationsMinimum Server Requirements Performance Badging / Workstation Requirements Digital Camera Minimum Badging / Workstation RequirementsUSB Camera WebCam Signature Capture