Wiring And Powering Up S-PCON-U | Pelco c3653m-a specs

Wiring And Powering Up S-PCON-U

Chapter 3: S-PCON-U (Power Connector)

Wiring And Powering Up S-PCON-U

When the S-PCON-U is connected to a PoE enabled switch, electronics inside the S-PCON-U signal the PoE switch to place power onto the input ethernet cable. This power is then directed by the S-PCON-U onto the output RJ45 Ethernet connector. When the S-PCON-U is connected to a non-PoE enabled switch it is necessary to provide an external power supply to the S-PCON-U. This DC power is then directed onto the output RJ45 Ethernet connector. If both a PoE enabled switch and DC power are connected to the S-PCON-U, priority is given to the DC power supply.

Important: The S-PCON-U device and its Power Supply must be installed within the protected area (locked area) of the access facility to meet UL requirements.

@

22.9-24VDC@1A

@

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

S-PCON-U Wiring and Powering up Diagram

The output LED on the S-PCON-U provides visual feedback that the device is functioning. The LED can be illuminated green to indicate output voltage is greater than 24 VDC, amber to indicate that output voltage is between 22 and 24 VDC, or red to indicate that output voltage is below 22 VDC.

Warning: When the S-PCON-U is operating DO NOT CONNECT any ethernet device other than an S-EIDC-U to the output RJ45 connector. Damage to electronics inside the connected ethernet device could result.

Important: It is important to maintain correct polarity when connecting a DC supply to S-PCON-U. Check for proper connection of the DC supply on the provided plug prior to connecting the supply to the S-PCON-U.

Intelli-M Hardware Installation And Reference Guide

23

Image 23

Pelco c3653m-a manual Wiring And Powering Up S-PCON-U, S-PCON-UWiring and Powering up Diagram

Contents

C3653M-A11/08 Hardware Installation And ReferencePelco, Inc. Worldwide Headquarters Trademarks Preface Table of Contents Recessed Mounting Box FCC Declaration Of Conformity S-EIDC-U, S-PCON-U UL Compliance S-EIDC-U, S-PCON-UOfficial Notices Official Notices Intelli-MHardware Overview Using This Manual Chapter 1 Intelli-M Hardware Overview Contents S-EIDC-U Intelli-MHardware Overview Chapter 1 Intelli-MHardware Overview Using This Manual Chapter 1 Intelli-MHardware Overview Chapter 2 S-EIDC-U ethernet Integrated Door Controller Contents S-EIDC-UOverview Technical Features S-EIDC-U Wiring S-EIDC-UDoor ComponentsS-EIDC-UDoor Component Wiring Keep in mind the following points Step 2: Wire the status, shunt, and exit inputsStep 3 Wire the readers Keep in mind the following points Four Power Options Powering Up An S-EIDC-U Determining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP Addressing Setting A DHCP IP Address Within The S-EIDC-U Quick Mount Assembly Breakdown Resetting An S-EIDC-UQuick Mount Assembly Page S-PCON-UOverview Chapter 3 S-PCON-U Power Connector ContentsWiring And Powering Up S-PCON-U S-PCON-UOverview Technical Features S-PCON-UWiring and Powering up Diagram Wiring And Powering Up S-PCON-U Chapter 3 S-PCON-UPower Connector S-EIDC-UWiring Terminals Chapter 4 Wiring Connections And ConfigurationsContents Sample S-EIDC-UGlobal Configuration S-EIDC-U Sample S-EIDC-UGlobal ConfigurationChapter 4 Wiring Connections And Configurations S-EIDC-UWiring Terminals S-EIDC-U Single Door Door Configuration With S-EIDC-U eFamily Update Procedure Appendix A eFamily Update UtilityContents Installing The eFamily Update Utility Web Interface Users Installing The eFamily Update Utility2.Launch double click the “setup.exe” file Supervisor Plus Users 6.Click the “Close” button Before Updating Your eFamily Device eFamily Update Procedure Figure A-7 Connection Information Screen Figure A-6 Choice To Backup ScreenFigure A-5 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-13 Update Complete Screen Figure A-12 Update In Process Screen Figure A-14 Example Error Message Errors That Occur During UpdatePage Output Configuration Appendix B Demo Kit WiringDefaults Input Configuration Alarm Service Configuration Controller ConfigurationAccess Service Configuration Ethernet Integrated Door Controller S-EIDC-UTechnical SpecificationsDimensions Quick Mount Assembly Kit Enclosure Inputs PowerCommunication Reader Ports Power Connector Module S-PCON-U S-PCON-UTechnical Specifications Power ControllerOperational Dimensions DC Power --22.9 to 24 VDC, 1A Power InDC Power --24 VDC, 1A Power Out Performance Badging / Workstation Requirements Miscellaneous Computer Hardware SpecificationsPerformance Communications Server Requirements Minimum Server Requirements Signature Capture Minimum Badging / Workstation RequirementsDigital Camera USB Camera WebCam