Installing The eFamily Update Utility | Pelco c3653m-a manual

Installing The eFamily Update Utility

Appendix A: eFamily Update Utility (Backup, Upgrade, And Restore eFamily Device Software)

Installing The eFamily Update Utility

Installation of the eFamily Update Utility is dependent on Intelli-M®Supervisor Plus or the Intelli-M®Web Interface.

Note: The Supervisor Plus software has not been UL verified.

Supervisor Plus Users

The eFamily Update Utility can be found on the Intelli-M Supervisor Plus installation CD. Once the CD is placed into the CD-ROM drive, right-click on the CD-ROM drive icon within “My Computer” and select “Open.” Navigate to the eFamily Update Utility folder, and then follow the installation procedure steps below.

Web Interface Users

The eFamily Update Utility file can be downloaded from the Pelco Web site at: www.pelco.com.

Installation Procedure

The procedure for installing the eFamily Update Utility is as follows:

1. If the file was downloaded from the Web site, unzip the downloaded file.

Important: Make a note of where you unzip the file contents, as you will need the unzipped files during the update procedure.

2.Launch (double click) the “setup.exe” file.

The welcome screen for the install wizard screen similar to that shown in Figure A-1 will be displayed.

Figure A-1: Setup Welcome Screen

3.Click the “Next” button.

The installer select installation folder screen similar to that shown in Figure A-2 will be displayed.

30	Intelli-M Hardware Installation And Reference Guide

Image 30

Pelco c3653m-a Installing The eFamily Update Utility, Supervisor Plus Users, Web Interface Users, Click the “Next” button

Contents

Hardware Installation And Reference Pelco, Inc. Worldwide HeadquartersC3653M-A11/08 Preface Trademarks Table of Contents Recessed Mounting Box UL Compliance S-EIDC-U, S-PCON-U Official NoticesFCC Declaration Of Conformity S-EIDC-U, S-PCON-U Official Notices Chapter 1 Intelli-M Hardware Overview Contents Intelli-MHardware Overview Using This Manual Intelli-MHardware Overview S-EIDC-U Using This Manual Chapter 1 Intelli-MHardware Overview Chapter 1 Intelli-MHardware Overview ethernet Integrated Door Controller Contents Chapter 2 S-EIDC-U Technical Features S-EIDC-UOverview Wiring S-EIDC-UDoor Components S-EIDC-UDoor Component WiringS-EIDC-U Keep in mind the following points Step 2: Wire the status, shunt, and exit inputsStep 3 Wire the readers Keep in mind the following points Powering Up An S-EIDC-U Four Power Options Determining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting A DHCP IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP Addressing Resetting An S-EIDC-U Quick Mount AssemblyQuick Mount Assembly Breakdown Page Chapter 3 S-PCON-U Power Connector Contents Wiring And Powering Up S-PCON-US-PCON-UOverview Technical Features S-PCON-UOverview Wiring And Powering Up S-PCON-U S-PCON-UWiring and Powering up Diagram Chapter 3 S-PCON-UPower Connector Sample S-EIDC-UGlobal Configuration Chapter 4 Wiring Connections And ConfigurationsContents S-EIDC-UWiring Terminals Sample S-EIDC-UGlobal Configuration Chapter 4 Wiring Connections And ConfigurationsS-EIDC-U S-EIDC-UWiring Terminals Single Door Door Configuration With S-EIDC-U S-EIDC-U Installing The eFamily Update Utility Appendix A eFamily Update UtilityContents eFamily Update Procedure Supervisor Plus Users Installing The eFamily Update Utility2.Launch double click the “setup.exe” file Web Interface Users 6.Click the “Close” button eFamily Update Procedure Before Updating Your eFamily Device Figure A-6 Choice To Backup Screen Figure A-5 Connection Information ScreenFigure A-7 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-12 Update In Process Screen Figure A-13 Update Complete Screen Errors That Occur During Update Figure A-14 Example Error MessagePage Input Configuration Appendix B Demo Kit WiringDefaults Output Configuration Controller Configuration Access Service ConfigurationAlarm Service Configuration Quick Mount Assembly Kit Enclosure S-EIDC-UTechnical SpecificationsDimensions Ethernet Integrated Door Controller Reader Ports PowerCommunication Inputs Dimensions S-PCON-UTechnical Specifications Power ControllerOperational Power Connector Module S-PCON-U Power Out Power InDC Power --24 VDC, 1A DC Power --22.9 to 24 VDC, 1A Minimum Server Requirements Miscellaneous Computer Hardware SpecificationsPerformance Communications Server Requirements Performance Badging / Workstation Requirements USB Camera WebCam Minimum Badging / Workstation RequirementsDigital Camera Signature Capture