Recommended communication settings on DL-01 | Pentax R-325(N), R326

PSF Software Ver.365

6.XON/XOFF: OFF

Please note that these settings should be common with DL-01's.

b-4 Recommended communication settings on DL-01

To configure DL-01 Communication setting, please read "Configuring the software" in the Help topics of DL-01. And select values as follows.

For setting “Type of Device” in the "Settings" panel (Menu—“Edit”--”Settings”),

select “PCS-300/R-100(PCS)/R-300(PSF)” for “R-300 PentaxSpecificationFunction” and other setting should be as follows.

(Please note that these settings should be common with Ｒ-300's. And if the selection of “Type of Device” is not collect it may result in missing some data.)

R-300BPC(DL-01)
Bits per second:	1200 (1200-9600 for sending "SURVEY DATA")
Databits:	8
Parity:	None
Stop bits:	1
PC(DL-01)BＲ-300
Bits per second:	1200
Databits:	8
Parity:	None
Stop bits:	1

c) Note for the Memory capacity

Data transfer failure from DL01 to R-300 may cause reduction of memory capacity. If memory capacity becomes less, please back up required data first, and then initialize coordinates data. To initialize coordinates data, turn on the instrument while pressing [F2]+[F5]+[ON/OFF] keys, and take your finger off from [ON/OFF] again.

After you see the message "COORD. DATA INITIAL", press [F5] key. Then the message "Please,

wait" is displayed. When it is completed, the panel of Electronic Vial is displayed.

49

Image 50

Pentax R-325(N), R-335(N), R-323(N), R-322(N), R326 instruction manual Recommended communication settings on DL-01

Contents

Special Functions PSF Software Ver.365 Document Ver Copyright ENT PowerESC Help Disp MeasTarget Mode Relations between memories and each Special function Contents Resection DataLink DL- 01 Software Introduction Introduction COORD.STAKEOUT can be Accessing the Special FunctionsExample COORD. Stakeout Accessing by Help KEY Accessing the Special Functions 000 109 COORD. Stakeout General pictures of measurement JOB Name input Alphanumeric keys and arrow key JOB Name selection Number screen Station Coordinates Station Coordinates inputNumber List screen Station Coordinate which is Coordinates Input screenInput the Y and Z Coordinate ENT key to view the Instrument Height Input screen Search and call of the stored Station CoordinatesBacksight Selection screen is viewed Number screen Input the Backsight point number Backsight Selection a. Coordinates inputCoordinates Input Backsight Point Number Search and Call of the stored Backsight Point NumberForesight Number List screen after Confirm the Backsight Point Coordinates Procedures 2 of 3. Stakeout Input and Stakeout of Foresight Point Number and Coordinates Compare screen Input the Foresight point numberInput the Foresight point Coordinates Aim at the Backsight point and input Azimuth angle in case Rotate the instrument horizontally and stop Search and Call of the stored Foresight Point Number Distance Stakeout ENT Dist Compare Distance StakeoutDistance Stakeout ENT Track / Meas Reference Point RDMREF.P-P REF.P.-P Observation of the reference point Observation of the target point P1 JOB Name ENT Coordinates JOB Name Input CoordinatesJOB Name ENT Coordinate JOB Name Input Search and call of stored Station Coordinates Search and call of the stored Backsight P. Number Azimuth input Store / ENT Measured PointENT Description Select Description Input Prism H Offset Point Offset ShotsH are offset value Obstacle JOB Name input Selection keys JOB Name selection Selection keys , ⇒ Coordinates Input ENT Coordinates input Backsight Coordinates inputSearch and call of the stored Backsight Coordinates Select Description Input ENT Coordinate Offset point survey Target point survey Observing the target REMObserving the reference point ENT Input Prism H Stored JOB Name selection Selection keys , ⇒ ResectionJOB Name input Selection keys , ⇒ ENT Station Point Input Point B survey Point C survey Prism H Select Description Select Resection Descriptioninput ENT ENT YSelect ENT Prism H Select ENT JOB Name ENT Survey JOB Name Input Data StorageJOB Name selection Selection keys ∆ , ∇ JOB Name ENT Survey JOB Name ENT INSTR. H Station Setup ENT Station Point InputENT Description Select ENT Store Select Memory Manager Send by input of the stored Coordinates JOB Name Select Baud Rate Memory ManagerShift to a desired JOB Name ENT Receive Delete by input of the Coordinates JOB Name Delete by search of the Coordinates JOB Name Survey Data Send ENT Send by input of the Survey JOB NameSearch & shift to stored JOB Name Send by search & call of the Survey JOB Name ENT Over Write Delete by input and call of the Survey JOB NameDelete by search and call of the Survey JOB Name Memory Manager ENT DataLink DL- 01 Software Recommended communication settings on DL-01 PN,X,Y,Z,Code Mail international@piic.pentax.co.jp First edition TS01101EB2