Step

6

Set the Boundary Width and Test the Receiver Collar

The Boundary Control Switch on the side of

6A

the Fence Transmitter has three settings (6A).

 

Setting B is used for most properties. The

 

following table will indicate the setting you

 

should use.

 

 

 

 

 

Amount of Wire

Setting

 

Up to 396 m (1300 ft)

B

 

396-732 m (1300-2400 ft)

C

 

Greater than 732 m (2400 ft)

A

 

Use the Boundary Width Control knob to set the width of the Warning Zone and Static Correction Zone (6B). Set the Boundary Width as wide as possible to give your pet the widest Warning and

Static Correction Zones without reducing the Pet Area too much. We recommend a 3.7-6 m (12-20 ft) Boundary width.

Note:The BoundaryWidth Control knob does not change the Static Correction Level.

To identify the Warning and Static Correction Zones, make sure the Receiver Collar battery is properly installed, the Static Correction Level is set at 2 or above, and the Test Light contacts are held to the Contact Points (6C). For best results, select a section of straight Boundary Wire that is at least 15 m (50 ft) long. Hold the Test Light tool contacts to the Contact Points.Walk toward the Boundary Wire with Contact Points pointing up and holding the Receiver Collar at your pet’s neck level (6D) until the Receiver Collar beeps (6E) and the Test Light Tool flashes.

6B

4

5

6

 

3

 

7

28

1

9

0

10

4

5

6

 

3

 

7

28

1

9

0

10

6C

Note:The Receiver Collar is waterproof, which can make the beep hard

6D

 

to hear.

 

If the Receiver Collar does not beep at the desired range, adjust the Boundary Width Control knob to the desired setting. Turning the Boundary Width Control knob clockwise increases the Boundary Width while turning it counterclockwise decreases it (6B). Repeat this activity as needed until the Receiver Collar beeps at the desired distance from the Boundary Wire.

The numbers on the Boundary Width Control knob indicate signal strength and are not representative of Boundary Width footage. If

adjusting the Boundary Width Control knob does not give the desired range, adjust the Boundary Control Switch to another setting to achieve your desired range. If using a Double Loop, you may need to increase the separation of the Boundary Wire to achieve the desired range.

6E

Boundary

Wire

6F

Boundary

The Receiver Collar beeps as a warning tone and ticks when delivering a Static Correction.

Wire

After hearing the beep, continue to walk towards the wire. The Receiver Collar should tick and

 

the Test Light should flash, indicating the Static Correction as you enter the Static Correction

 

Zone (6F). A warning tone and the flashing of the Test Light indicate that the Receiver Collar

 

and the system are working properly. Test in a number of different areas until you are satisfied

 

that the system is functioning properly. Next, walk all around the Pet Area to ensure there are

 

no areas where the Receiver Collar may activate from signals coupled onto buried wires or

 

cables. Test the collar in and around the inside of the house as well. As mentioned, cable and wires from cable TV, electrical or telephone lines may conduct pet fencing signals inside and outside the house that can activate the dog’s collar accidentally.While rare, if this occurs your Boundary Wire is probably too close to these outside lines and should be moved or modified as shown in Figure 3A.

If you are satisfied that your system is functioning properly, you are ready to start burying the Boundary Wire. If the Receiver Collar did not beep or the Test Light did not flash, see the “Troubleshooting” section.

Note:The BoundaryWidth is broken down into 20%Warning Zone and 80% Static Correction Zone.

10

www.petsafe.net

Page 10
Image 10
Petsafe PIG20-11041 manuel dutilisation Set the Boundary Width and Test the Receiver Collar, Amount of Wire Setting

PIG20-11041 specifications

The PetSafe PIG20-11041 is a state-of-the-art in-ground pet fence system designed for dog owners who value safety, freedom, and reliability. This system provides a secure boundary for your pets, allowing them to roam freely within a predetermined area while ensuring that they stay away from hazardous zones like roads or neighboring properties. The PetSafe PIG20-11041 is particularly known for its advanced technologies and customizable features.

One of the standout features of the PetSafe PIG20-11041 is its adjustable collar. The collar is lightweight and designed for comfort, ensuring it fits snugly without causing irritation to your pet. It includes a built-in battery that is easy to replace, and the system typically features several levels of static correction. This allows you to customize the training intensity based on your dog's temperament and learning pace.

Another significant characteristic of the PetSafe PIG20-11041 is its compatibility with multiple dogs. The system can accommodate an unlimited number of pets with additional collars, providing a great solution for households with multiple furry companions. This flexibility is an excellent advantage for families that want to maintain consistent boundaries for all their pets.

The installation process of the PetSafe PIG20-11041 is designed to be user-friendly. The included steps allow pet owners to create a secure boundary by burying copper wire underground, enabling seamless integration with your yard. The system can cover up to 25 acres, making it ideal for larger properties, and the wire can be run in various configurations to suit the layout of your yard.

The PetSafe PIG20-11041 also incorporates a tone-only mode, which can be used during training sessions to help your dog learn the boundaries without any static correction. This feature is particularly beneficial for younger or more sensitive dogs, as it allows them to acclimate to the system in a more gentle manner.

Durability is another defining characteristic of the PetSafe PIG20-11041. The system is built to withstand various weather conditions, ensuring that it remains functional and reliable over time. Moreover, the collar is waterproof, allowing your pets to enjoy outdoor activities without fear of damaging the containment system.

In summary, the PetSafe PIG20-11041 is a comprehensive in-ground pet containment system that prioritizes safety and flexibility. With its adjustable collar, multi-pet compatibility, straightforward installation, and durable design, it represents a smart investment for pet owners who want to provide their dogs with the freedom to enjoy their surroundings while maintaining secure boundaries.