Manuals / Philips / Computer Equipment / Laptop

Philips CF-30FTSAZAM service manual Assembly of Power SW, 7-18, Safety Working

Models: CF-30FTSAZAM

1 85

Download 85 pages 41.18 Kb

Page 39

■Assembly of Power SW

■Assembly of Power SW

Attach the Battery Cushion

Battery Pack Insertion Slot

* Notes:

1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

12 2

25 2

3

5

Tighten of Screw

Top

Connection Direction

Bottom

Cable Power

Connection

CAB Wall

Connection Direction

FPC Power SW is set

Power SW LED Panel is set

Attach the Battery Slide Sheet (on Battery Cushion)

Avoid air leaking into it. Avoid coming off 4 corners. Fit to the line.

10 1

Attach the DC Gasket

Ensure the upper and lower Flex holes match.

S3	Safety Working

Attach the TP

FPC Tape

Match the Cabinet slit and the tape slit.

Do not run the Cabinet edge out of the tape slit.

CAUTION

S1:Insulation S2:Pinching Cables S3:Sharp Edge S4:Part No. Check S5:Others

7-18

Image 39

Philips CF-30FTSAZAM service manual Assembly of Power SW, 7-18, Safety Working

Contents

M …for U.S.A. and Canada Model No. CF-30FTSAZAMNotebook Computer ORDER NO. CPD0711216CEFor U.K How to replace the fuseLITHIUM BATTERY Important Safety InstructionsSAFETY PRECAUTIONS LITHIUM BATTERYPrecautions Battery Pack CONTENTS Main Specifications 1. SpecificationsMain Specifications Wireless LAN <Only for model with wireless LAN>BluetoothTM <Only for model with Bluetooth> 2. Names and Functions of Parts A B C D E F G H J H K LM N O P R BIOS Diagram3 Block 2nd-Li-Ion Battery Pack4.1. Basic Procedures 4 Diagnosis ProcedureFlow Chart 4.2. Troubleshooting5 Power-OnSelf Test Boot Check Error Diagnosis by Checking Beep Signal SoundOutline of POST 0200 Failure Fixed Disk 02F0: CPU ID 7 Self Diagnosis Test 1-2.When you execute an automatic test1-3.When you execute the enhancing test 2. Operation of PC-DiagnosticUtility 2-1.Selection of tested device 2-2. PC-Diagnosticutility End method3. Test Item and Division of trouble Test Item Wiring Connection Diagram 7.1.1 7 Disassembly/ReassemblyDisassembly Instructions 7.1.2. Removing the Battery Pack and HDD7.1.3.Removing the HDD 7.1.6.Removing the GPS PCB and Blue- tooth PCB 7.1.8.Removing the USB PCB and Antenna PCB 7.1.7.Removing the DIMM Cover and Bot- tom Cover7.1.9.Removing the FPC HDD BAT 7.1.10. Removing the PAD PCB7.1.11.Removing the Main PCB CN400,CN401 11.Remove the 2 Screws. <N6> 7.1.13. Removing the I/O PCB 7.1.15. Removing the Handle and Power SW 7.1.16. Removing the Display Unit 7.1.19. Removing the Antenna PCB L and R 7.2.Reassembly Instructions 7.2.1.Attention when CF-30series is repaired7.2.2.Setting the Antenna PCB L and R Do not pinch the cable Safety WorkingInsert the cable between the pins Do not pinch the cable out of the cabinet2.Attach the 2 drop holders N0GF1J000009without T.S Assembly of LCD UnitPreparation of Inverter 7-147.2.4.Setting the LCD Rear Cabinet, Hinge L and R 7.2.6.Setting the Handle and Power SW 7.2.5.Setting the Display Unit1.Set the SW LED PCB Assembly of Power SW Safety Working7-18 Assembly of Palm Top Cover 7-19Cover 7.2.8.Setting the I/O PCB 7.2.9.Setting the SD PCB, Express Cardand PCMCIA Card 7.2.10. Setting the Main PCB Screws <N7>: DRSB26+10HKL Connector CN2724.Fix the Screw. <N7> 25.Attach the TOP Screws Screws <N6>: DRQT26+E4FKLSafety Working Safety Working12 Safety Working Safety WorkingSafety Working 7.2.11.Setting the PAD PCBSafety Working Safety Working7.2.12. Setting the FPC HDD BAT Page 4.Fix the USB PCB using the Screws. <N6> 7.2.13. Setting the USB PCB and Antenna PCB1.Open the Connector Cover 2.Fix the Antenna PCB using the 2 Screws. <N3>Safety Working Assembly of USB PCBSafety Working Safety Working7.2.14. Setting the DIMM Cover and Bottom Cover 7-30 Safety WorkingSafety Working Preparation of DIMM Cover4.Connect the Cable to the Connector. CN25 7.2.15. Setting the GPS PCB and Bluetooth PCB2.Connect the Cable to the Connector on GPS PCB 3.Fix the GPS Ass’y using the 4 Screws. <N12>Screws <N29>: DRQT26+E3FNL 1.Set the Keyboard onto the Computer2.Connect the 2 Cables to the 2 Cables. CN13,CN14 4.Set the LCD Cable Plate7.2.18. Setting the HDD HDD TAPE S Safety WorkingPreparation oh HDD ASSY 7-34HDD Cushion Black Metal Plate Do not place the damper over the plate of FPCDo not place the damper over the plate of heater NotesHDD Cushion Black Metal Plate HDD Thermal PlateHDD Side Damper B-BSECA-ASEC Page 7.2.19. Setting the Battery Pack and HDD Pack 1. Set the HDD Pack 2. Set the Battery Pack7-39 Screw tightening torque 10 Exploded ViewA 0.19 ± 0.02 N.m A 0.19 + 0.02 N.m S0.19 + 0.05 N.m 2.0 + 0.5 kgf.cm K1213B0.45 + 0.05 N.m 4.5 + 0.5 kgf.cm P0.8 + 0.1N.m 8.0 + 1.0 kgf.cm R0.3 + 0.05 N.m 3.0 + 0.5 kgf.cmG N9 D 0.314 + 0.0196 N.m 3.2 + 0.2 kgf.cm A 0.19 + 0.02 N.m 2.0 + 0.2 kgf.cmB 0.45 + 0.05 N.m 4.5 + 0.5 kgf.cm C 0.216 + 0.0196 N.m 2.2 + 0.2 kgf.cmB N7 Replacement Parts List CF-30FTSAZAMREF. NO and AREA Accessories Packing MaterialMechanical Parts K2-5-4 K2-4-3DFUQ0113ZA SD LATCH SPRINGK2-20 DFKM8184ZA-0 DFWV80C0513LCD REAR CABINET ASSY K13-1DFHR3619ZA K1201 PART NO Replacement Parts ListCF-30FTSAZAM REF. NO and AREAC 55, 72, 91, 152, F1G1H470A542 D 33, 34, 35, 36, 37, IC 79, 80, Q 79, 105, 106, 113, R 85, 88, 245, 491, ERJ2RHD104X ERJ2GEJ333XRESISTOR, 1/16W, 33KΩ 341, 367, 371,IO PCB MP PCBPAD PCB LED PCB HDD BATTERY FPCSD PCB USB PCBBT PCB