Pioneer DEH-P9100R operation manual Installation Manual, CRD3473-A UC KMMUF/01K00000

INSTALLATION MANUAL

DEH-P90HDD

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA.

Printed in Japan

Imprimé au Japon

<CRD3473-A> UC <KMMUF/01K00000>

MANUEL D’INSTALLATION

Connecting the Units

Note:

•This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recre- ational vehicle, truck, or bus, check the battery voltage.

•To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before beginning installation.

•Refer to the owner’s manual for details on con- necting the power amp and other units, then make connections correctly.

•Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

•Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake, and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insula- tion of the wiring melts or gets torn, there is a dan- ger of the wiring short-circuiting to the vehicle body.

•Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.

•Do not shorten any leads. If you do, the protection circuit may fail to work when it should.

•Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

•When replacing fuse, be sure to use only fuse of the rating prescribed on the fuse holder.

•Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or the left and right ≠ speaker leads are common.

•If the RCA pin jack on the unit will not be used, do not remove the caps attached to the end of the con- nector.

•Speakers connected to this unit must be high- power types with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catch- ing fire, emitting smoke, or becoming damaged.

•When this product’s source is switched ON, a con- trol signal is output through the blue/white lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control ter- minal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal.

•When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and malfunction.

•To avoid short-circuiting, cover the disconnected lead with insulating tape. Especially, insulate the unused speaker leads without fail. There is a possi- bility of short-circuiting if the leads are not insulat- ed.

•To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same colors correctly.

•If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehi- cle for several hours. (Fig. 1)

		CC
	F	A	O				F	O
			N				F	N
O	F					O
					S					S
					T					T
				R	A			T	R	A
			T
ACC position						No ACC position

Fig. 1

•The black lead is ground. Please ground this lead separately from the ground of high-current prod- ucts such as power amps.

If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire.

•Cords for this product and those for other prod- ucts may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied Installation manuals of both products and connect cords that

have the same function.