TROUBLESHOOTING
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in use.
If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.
Symptom | Possible Cause | Remedy |
|
|
|
No power. | • The power cord has not been connected. | • Connect to power outlet. |
|
|
|
No sound, or sound volume is | • AUDIO INPUT switch is set incorrectly. | • Set AUDIO INPUT switch to select the currently |
too low. |
| playing component. |
| • Connection cables are not connected properly, | • Connect correctly. |
| or are disconnected. |
|
| • Connentors or plugs are dirty. | • Clean away any dirt before connecting. |
| • The rear panel MASTER ATT. switch is set to | • Adjust rear panel MASTER ATT. switch. |
|
| |
|
|
|
No microphone sound from | • The OUTPUT TO BOOTH MONITOR (P. 42) is set | • Set OUTPUT TO BOOTH MONITOR (P. 42) to ON. |
BOOTH output. | to OFF. |
|
|
|
|
No digital output. | • The digital output sampling frequency (fs) does | • Set rear panel sampling frequency selector to |
| not match the specifications of the connected | match the specifications of the connected |
| component. | component. |
|
|
|
Sound is distorted. | • Audio master output level is too high. | • Adjust AUDIO MASTER LEVEL dial or the rear |
|
| panel MASTER ATT. switch. |
| • Input level is too high. | • Adjust the AUDIO TRIM dial so that the input |
|
| level approaches 0 dB on the channel level |
|
| indicator. |
|
|
|
Cross fader doesn’t work. | • CROSS FADER ASSIGN switch setting ([A], | • Correctly set the CROSS FADER ASSIGN switch |
| [THRU], [B]) is incorrect. | for the desired channel. |
|
|
|
Can’t perform fader start with | • The FADER START button is set to OFF. | • Set the FADER START button to ON. |
DVD/CD player. | • Rear panel CONTROL connector is not | • Use a control cable to connect the CONTROL |
| connected to DVD/CD player. | connectors of mixer and DVD/CD player. |
| • Only the rear panel CONTROL connector is | • Connect both the CONTROL connectors and |
| connected to the DVD/CD player. | analog input connectors. |
|
|
|
Effects don’t work. | • Effect channel selecter (CH SELECT) setting is | • Correctly select the channel on which you wish |
| incorrect. | to apply effects. |
| • Effect parameter 2 dial (LEVEL/DEPTH) is set to | • Adjust the effect parameter 2 dial (LEVEL/ |
| [MIN]. | DEPTH). |
|
|
|
BPM can’t be measured. | • Input level is too high, or too low. | • Adjust the AUDIO TRIM dial so that the input |
Measured BPM value is |
| level approaches 0 dB in the channel level |
incorrect. |
| indicator. |
|
| • Adjust other channels as well so that the input |
|
| levels approach 0 dB in the channel level |
|
| indicator. |
| • BPM may not be correctly measurable with | • Strike the TAP button to set BPM manually. |
| some tracks. |
|
|
|
|
The measured BPM value is | • Some differences may occur due to differences | • No remedy is necessary. |
different from the value | in BPM detection methods. |
|
published with the DVD/CD. |
|
|
|
|
|
MIDI sequencer can’t be | • MIDI sequencer’s synch mode is not set to | • Set MIDI sequencer’s sync mode to “slave”. |
synchronized. | “slave”. |
|
| • MIDI sequencer is not supported type. | • MIDI sequencers that do not support MIDI |
|
| timing clock cannot be synchronized. |
|
|
|
45
En
