Pioneer VSX-1014TX manual Other audio problems, Digital inputs on

12Additional information

Symptom Cause Remedy

No sound from one speaker.

• The speaker setting has been set to NO.	• Change the setting in Speaker Setting on page 44.
• The speaker level is too low.	• Check the level in Channel Level on page 45.
• The speaker isn’t connected properly.	• Check Connecting the speakers on page 20 to make sure
	the speaker is connected correctly.

•The source has no sound output for that channel.

•By choosing an advanced effect listening mode (see Listening in surround sound on page 30), you may be able to create an extra channel for the speaker.

Sound is produced from analog components, but not from digital ones (DVD, LD, CD-ROM etc.).

• The digital input assignment is wrong.	• Assign the digital inputs correctly (see Assigning the
	digital inputs on page 60).
• The digital components aren't connected	• Make sure you have properly connected the digital
properly.	component to the corresponding input on the back of the
	receiver (see Connecting up on page 14).
• The player is not compatible with the source	• Choose a compatible source, or check the component’s
you're using, or the player settings are	manual for the correct settings.
incorrect.
• The digital output level has been turned	• Set the digital volume level of the player to full, or to the
down on a CD recorder or other component	neutral position.
equipped with digital output level adjustment
capability.
• The multichannel analog inputs are	• Press MULTI CH IN again (see Selecting the
selected.	multichannel analog inputs on page 37).
• The input signal type is set to ANALOG.	• Set the input signal type to DIGITAL (see Choosing the
	input signal on page 33).

No sound is output or a noise is output when Dolby Digital/DTS software is played back.

• A DVD player not compatible with Dolby	• Make sure your DVD player is compatible with Dolby
Digital/DTS is being used.	Digital/DTS.
• The settings on the DVD player are incorrect	• Make sure the player's settings are correct and/or the
and/or the DTS signal output is turned off.	DTS signal out is on. Refer to the instruction manual
	supplied with the DVD player.
• The digital output level is turned down on a	• Set the digital volume level of the player to full, or to the
CD player or other component equipped with	neutral position.
digital output level adjustment capability. (The
DTS signal has been altered by the player, and
cannot be read.)

Other audio problems

Symptom Cause Remedy

Broadcast stations cannot be selected automatically, or there seems to be considerable noise in radio broadcasts.

FM broadcasts
• The FM antenna is not fully extended or is	• Fully extend the FM wire antenna, position for best
poorly positioned.	reception, and secure to a wall.
• Weak radio signals.	• Connect an outdoor FM antenna (see page 19).
AM broadcasts
• The AM antenna is poorly positioned.	• Adjust the direction and position for best reception.
• Weak radio signals.	• Connect an additional internal or external AM antenna
	(see page 19).

•Interference caused by other equipment (fluorescent lamp, motor, etc.).

•Turn off the equipment causing the noise or move it away from the receiver.

•Place the antenna farther away from the equipment causing the noise.

A multi channel DVD source	• The source is coming from something other	• Check the MULTI CH IN connections (see Connecting
appears to be downmixed from 2 than the MULTI CH IN jacks (for example,		multichannel analog components on page 17) and select
channels during playback.	digital PCM output, etc.)	the multichannel analog inputs with the MULTI CH IN
		button (see Selecting the multichannel analog inputs on
		page 37).
Noise is output when scanning a • The scan function performed by the player		• This is not a malfunction, but be sure to turn the volume
DTS CD.	slightly alters the digital information, making	down to prevent the output of loud noise from your
	it unreadable.	speakers.
When playing a DTS format LD	• The input signal type is set to ANALOG.	• Set the input signal type to DIGITAL (see Choosing the
there is audible noise on the		input signal on page 33)
soundtrack.

66

En