Additional information | 12 |
Symptom | Cause | Remedy |
Can't record audio. | • You are trying to make an analog recording | • You can only record analog to analog, or digital to |
| from a digital signal, or a digital recording of | digital. |
| an analog source. |
|
|
|
|
| • The digital source is copy protected. | • You can't record digital sources that have been copy |
|
| protected. |
|
|
|
| • The analog REC jacks have not been | • Check your analog connections (see Connecting analog |
| connected properly. | audio components on page 17). |
|
|
|
Subwoofer output is very low. | • The speaker settings result in very little | • To route more audio signal to the subwoofer, set it to |
| audio signal being sent to the subwoofer. | PLUS, or select SMALL for the front speaker setting (see |
|
| Speaker Setting on page 44). |
Everything seems to be set up | • The speakers are out of phase. |
correctly, but the playback sound |
|
is odd. |
|
•Check that the positive/negative speaker terminals on the receiver are matched with the corresponding terminals on the speakers (see Connecting the speakers on page 20).
Noise or hum can be heard even | • There is electrical interference from another | • Check that personal computers or other digital |
when there is no sound being | component or appliance. | components connected to the same power source are not |
input. |
| causing interference. |
|
|
|
There seems to be a time lag | • The subwoofer channel can be delayed | • See Automatically setting up for surround sound |
between the speakers and the | slightly if run through a | (MCACC) on page 11 to set up your system again using |
output of the subwoofer. |
| MCACC (this will automatically compensate for a delay in |
|
| the subwoofer output). |
|
| |
The maximum volume available | • The channel levels may have been adjusted. • This is not a malfunction. If the levels in Channel Level | |
(shown in the front panel display) |
| on page 45 have been adjusted, the maximum volume will |
is lower than the +12dB |
| change accordingly. |
maximum. |
|
|
|
|
|
Video
Symptom | Cause | Remedy |
|
|
|
No image is output when an input is selected.
• The video connections are incorrect.
•Make sure the video component is connected correctly (see page 18).
•You are using component video connections for your source, but not for your TV.
•Using the video converter, video signals can be converted from a composite or
| • You are using component video | • Check Assigning the component video inputs on page 61 |
| connections and the component video inputs | to make sure you’re assigned the correct input. |
| are assigned incorrectly. |
|
|
| |
| • The DVD/video player settings are incorrect. • Set correctly. Refer to the instruction manual supplied | |
|
| with the DVD/video player. |
|
|
|
| • The video input selected on the TV monitor | • Set correctly. Refer to the instruction manual supplied |
| is incorrect. | with the TV. |
|
|
|
| • The component video inputs are assigned | • Check Assigning the component video inputs on page 61 |
| to a video component connected only to the | to make sure the component video assign for that video |
| composite or | component is switched to OFF. |
|
|
|
The System Setup screen | • Some TVs connected to the receiver with | • When the receiver is in standby, switch to COLOR |
doesn't appear. | component video cables do not display the | BURST OFF by holding down the front panel ACOUSTIC |
| System Setup screen when the Color Burst | EQ button and pressing STANDBY/ON. (the current |
| feature is on. | setting appears in the display). |
|
|
|
Can’t record video. | • You are trying to record a source connected | • Connect the source component to either the composite |
| to the component video jacks. | video or the |
|
| components on page 18). |
|
|
|
| • The source is copy protected. | • You can't record sources that have been copy protected. |
|
|
|
| • The recorder's video input is hooked up | • Hook up the source and the recorder using the same |
| using a different type of cable to the source | type of video cable (see About the video converter on |
| video output. | page 15). |
|
|
|
67
En