Pioneer VSX-1014TX Settings, Display, 12Additional information, Symptom, Cause, Remedy, 96kHz

12Additional information

Settings

Symptom	Cause
The Auto MCACC Setup	• The ambient noise level in the room is too
continually shows an error.	high, or obstacles are blocking the setup
	microphone.

Remedy

•Keep the noise level in the room as low as possible when using the Auto MCACC Setup (see Other problems when using the Auto MCACC Setup on page 13 for more on this). If the noise cannot be kept low enough, you will have to set up the surround sound manually (page 43).

After using the Auto MCACC Setup, the speaker size setting (LARGE or SMALL) is incorrect.

•There was some inaudible low-frequency noise in the room.

•The low-frequency noise could have been caused by an air conditioner or motor. Switch off all appliances in the room and rerun the Auto MCACC Setup.

Display

Symptom Cause Remedy

The display is dark or off. • The display is set to dark or off.

•Press FL. DIMMER on the remote control repeatedly to select a different brightness.

After making an adjustment the	• The display is set to off.	• Press FL. DIMMER on the remote control repeatedly to
display goes off.		select a different brightness.
You can't get DIGITAL to display	• There is a problem with the digital	• Check your digital connections and/or assign the digital
when using the SIGNAL SELECT	connections or the digital input is assigned	inputs correctly (see Assigning the digital inputs on
button.	incorrectly.	page 60).
	• The multichannel analog inputs are	• Press MULTI CH IN again (see Selecting the
	selected.	multichannel analog inputs on page 37).
The Dolby/DTS indicator doesn't	• The player is paused.	• Press play.
light when playing Dolby/DTS
	• The player's sound output settings are	• Set the player correctly (consult the manual that came
software.
	wrong.	with the player, if necessary).
When playing a DVD-Audio disc,	• The audio from these discs is output from	• This is not a malfunction. See also the operating
the DVD player display shows 96	the analog audio jacks of the DVD player only;	instructions that came with your DVD player.
kHz. However, the receiver’s	the receiver does not show the sampling rate
display does not.	of the input signal through the analog inputs.
During playback of a DTS 96/24	• The receiver’s input signal type is set to	• Set the receiver to AUTO or DIGITAL (see Choosing the
source, the display doesn't show	analog.	input signal on page 33).
96kHz.
When playing Dolby Digital or	• No digital connection, or the digital	• Check the digital audio connection (page 16).
DTS sources, the receiver’s	connection is incorrect.
format indicators do not light.
	• The receiver’s input signal type is set to	• Set the receiver to AUTO or DIGITAL (see Choosing the
	analog.	input signal on page 33).
	• The DVD player is set to output Dolby Digital	• Check the settings on the player. Set the output for
	and/or DTS audio as PCM.	Dolby Digital and DTS (no PCM conversion). See also the
		operating instructions that came with your DVD player.
	• The disc has several playback audio tracks;	• Switch the playback audio channel on your DVD player.
	the one currently playing is actually PCM.	See the operating instructions that came with your DVD
		player.
When playing certain discs,	• The audio format of the disc is not 5.1/6.1	• This is not a malfunction. Check the disc packaging for
none of the receiver’s format	channel.	details of the audio formats available on the disc.
indicators light.
When playing a disc, the	• The input signal type is set to analog.	• Set the receiver to AUTO or DIGITAL (see Choosing the
2 PL II or Neo:6 indicator lights		input signal on page 33).
on the receiver.
	• A two channel soundtrack is currently	• This is not a malfunction. Check the disc packaging for
	playing.	details of the audio formats available on the disc.
	• The soundtrack currently playing is	• This is not a malfunction. Check the disc packaging for
	encoded using Dolby Surround.	details of the audio formats available on the disc.
During playback of a Surround	•The source may be Dolby Surround EX / DTS	• Set to Extended ON (see Using the surround back
EX or DTS ES source on the	ES software, but it has no flag to indicate it is	channel (Extended mode) on page 34) then switch to the
Extended AUTO setting, the EX	6.1 compatible.	THX Surround EX or Standard EX listening mode (see
and ES indicators don’t light, or		Listening in surround sound on page 30).
the signal is not properly
processed.

68

En