Preparations
Learning mode: Programming signals from other remote controls
(VSX-D509S only)
If preset codes are not available for your component(s), or the available preset codes do not operate correctly, you can use this function to program in signals from the remote control(s) of your other component(s). This operation can also be used after recalling a preset code to program additional operations not covered in the preset codes.
| SOURCE | RECEIVER |
|
DVD | TV | VCR | |
| MULTI CONTROL |
| |
RCV | CD | TUN | TVC |
1 2 3
MIDNIGHT 5.1CHATT
2 | 4 | 5 | 6 |
SIGNAL SELECT |
| EFFECT | |
| 7 | 8 | 9 |
+10 |
| DISC |
| 0 | ENTER |
TV CONTROL |
| |
| TV |
|
TV VOL | TVFUNC | MASTERVOLUME |
| MENU |
|
| CHANNEL | |
|
| FQ |
ST |
| ST |
| ENTER |
|
LED
2
2
2
1Press SETUP and hold for 3 seconds.
The visible LED will blink twice.
2Press the MULTI CONTROL button for the component you want to control and then press 9, 7, then 5 to select the LEARNING setup mode. The remote is ready to learn new
commands from other remote controls.
The LED flashes rapidly. | ) |
To cancel LEARNING setup mode | |
Press SETUP button. | |
After ten seconds if no commands are entered the remote will | |
(revert to its previous mode. |
| FQ |
|
8 |
|
|
D.ACCESS | BAND | CLASS |
3 | 1 | Á |
MPX | DTV ON / OFF | DTV MENU |
7 4 ¢ | ||
2 | DSP TEST TONE | |
CH SELECT | CH LEVEL | FL DIMMER |
LOUDNESS FUNCTION MUTING SETUP | 1,5 |
ë |
|
AV |
|
REMOTE CONTROL UNIT |
|
memo The highlighted keys can learn new functions.
| SOURCE | RECEIVER |
|
DVD | TV | VCR | |
| MULTI CONTROL |
| |
RCV | CD | TUN | TVC |
1 |
| 2 | 3 |
MIDNIGHT | 5.1CH | ATT | |
4 |
| 5 | 6 |
SIGNAL SELECT | EFFECT |
| |
7 |
| 8 | 9 |
+10 |
|
| DISC |
0ENTER
TV CONTROL
TV
TV VOL | TVFUNC MASTERVOLUME |
| MENU |
3Press the button to be programmed (for example the 3 [play] button).
4Point the remote controls at each other, about
1Point the remote controls toward each other.
2Press the button on the other remote control corresponding to the operation you wish to program. The LED on this receiver’s remote will go out and then blink twice when the operation is learned.
Press the teaching key repeatedly, varying the distances between the remotes, until you see this receiver’s remote blink twice, indicating the operation has been learned.
1 - 2 inches | 3 | 6 | 9 |
|
| Á | ¢ | ë |
| 2 | 5 | 8 | 0 |
| 1 | 4 |
|
| 1 | 4 | 7 |
| 8 | 3 | 7 | 2 |
To program additional operations for the current component
Repeat steps 3 and 4.
To program operations for another component
Repeat steps 2 through 4.
CHANNEL
FQ
ST | ST |
ENTER
FQ
8
D.ACCESS BANDCLASS
3 1 Á
MPX DTV ON / OFF DTV MENU
7 4 ¢
2 DSP TEST TONE
5Press SETUP to exit the LEARNING setup
mode
After ten seconds of inactivity the remote control will automatically leave the LEARNING mode and revert to its previous mode.
CH SELECT | CH LEVEL | FL DIMMER |
LOUDNESS FUNCTION MUTING | SETUP |
ë
AV
REMOTE CONTROL UNIT
memo | Some commands from other remote controls cannot be learned, | |
but in most cases the remotes just need to be moved closer | ||
| ||
| together a farther apant. |
26