Pioneer VSX-D409, VSX-D509S manual ADVANCED THEATER mode Dolby/DTS mode, Playing a Source

Sound Modes

ADVANCED THEATER mode ( Dolby/DTS mode)

Switch on the Dolby/DTS mode by pressing the 2surround button. When Dolby/DTS mode is ON, Dolby Pro Logic, Dolby Digital and DTS, and signal processing is performed automatically corresponding to the input signal. Use this button to cycle through the various modes.

For all modes other than STANDARD, DSP is switched on and will appears in the diisplay.

1Press RCV.

	SOURCE RECEIVER
1	DVD	TV VCR	CD-R		This sets the remote to select the sound mode. (On the D409 the
					button is called RECEIVER.)
		MULTI CONTROL
	RCV	CD TUN	TVC		(You can skip this step when using the controls on the
	1	2	3
					receiver.)
22	7￿	4￿	¢￿
	2	DSP TEST TONE
	CH SELECT	CH LEVEL	FL DIMMER	2	Switch the Dolby/DTS mode on and off by
					pressing 2 on the remote control or 2/
					DTS on the front panel.

ë￿	Each press changes the display as follows.
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR CD

	1			CD-R/		=STANDARD = MUSICAL = DRAMA
		RECEIVER TUNER TAPE/MD TVCONT
		2 DSPMODE MIDNIGHT 5.1CH
2	2	1	2	3	4	(OFF) + EXPANDED + ACTION +
		SELECT TONE		ATT	SELECT
		CHANNEL TEST			SIGNAL
		5	6	7	8
		CHANNEL		EFFECT
			LEVEL
		9	0	à	ENTER
				10	DISC

Refer to page 36 for more details about each surround effect.

2/DTS

memo

•The effects of Dolby/DTS mode can be adjusted in the range of 10 to 90 by pressing EFFECT +/– (the default setting is 70). Also, the effect level can be set in each Dolby/DTS mode by pressing the EFFECT +/– button. The STANDARD mode cannot be changed.

Playing a Source

		SOURCE	RECEIVER		2
	DVD	TV	VCR	CD-R	3
		MULTI CONTROL
	RCV	CD	TUN	TVC
	1		2	3
	MIDNIGHT		5.1CH	ATT
4	4		5	6
	SIGNAL SELECT		EFFECT
	7		8	9
	+10			DISC

0ENTER

CH SELECT CH LEVEL FL DIMMER

3 LOUDNESS FUNCTION MUTING SETUP

ë￿

1Turn on the power of the playback component.

2Turn on the power of the receiver.

Be sure that the standby indicator turns off on the front panel.

3Press MULTI CONTROL buttons or the FUNCTION button to select the source you

want to playback.

If the DIRECT FUNCTION is OFF you have to use the FUNCTION button to select the source (see p.28).

Operation

MULTI CONTROL		3
DVD/LD TV/SAT VCR/DVR	CD
CD-R/
RECEIVER TUNER TAPE/MD TVCONT

2DSPMODE MIDNIGHT 5.1CH

1 2 3 4

	CHANNEL	TEST	ATT	SIGNAL	4
	SELECT	TONE		SELECT
	5	6	7	8
	CHANNEL		EFFECT
3	LEVEL
	9	0	à	ENTER
	1￿ Á￿ 4￿ ¢￿
	LOUDNESS FUNCTION		MUTING
	RECEIVER	FL	REMOTE MASTER
		DIMMER	SETUP	VOLUME
2	AUDIO/VIDEOPRE-PROGRAMMED
	REMOTECONTROLUNIT

4If necessary, press SIGNAL SELECT to select the input signal corresponding to the source component (as above).

5Start playback of the component you selected in step 1.

41